HIKVISION DS-PDMC-EG2-WB, Manual, Page: 5 / 5

11 Specification
10 Operation Caution and Device Maintenance
- All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related
regulations in your local region.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment
installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
- Please make sure that the power has been disconnected before you wire, install or dismantle the device.
- If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service
center.
- Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetism radiation. Avoid the equipment
installation on vibrations surface or places subject to shock (ignorance can cause equipment damage).
- Do not place the device in extremely hot (refer to the specification of the device for the detailed operation temperature), cold, dusty or
damp locations, and do not expose it to high electromagnetic radiation.
- The device for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignorance can cause fire
danger).
- Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and
affecting the endurance of sensor at the same time.
- Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of
used batteries according to the instructions provided by the battery manufacturer.
- Do not expose the device to the corrosive gas. Otherwise the equipment damage may occur.
- Do not expose the device to the explosive situation.
5
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
Model DS-PDMC-EG2-WB/WE
Detec ti on Performance
Detec ti on Method Op ening Contact
Detec ti on G a p 43mm Ma x
Feature
Digital P rocessing S u pp ort
Ta mp er P rotec ti on F ront, R ear
E nviron m ent Te mp erature I ndicator S u pp ort
S ignal S trength I ndicator S u pp ort
Interface
Alar m I n p ut N or m ally Closed, N or m ally Op en, Imp ulse Count
P ower S witch P ower Up E nrolling
L E D I ndicator B lue ( Alar m)
Transmission
Trans m ission Technology Tri -X W ireless
Trans m ission Method Two -W ay RF W ireless
Trans m ission F re q uency 433/868 MHz
Trans m ission S ecurity A ES- 12 8 E ncry pti on
Trans m ission R ange (F ree Sp ace ) 1.2 Km(433 MHz )/ 1. 6Km(868 MHz )
F re q uency Ho pp ing S u pp ort
E nrolling Method P ower u p , R e m ote I D, QR Code
Electrical Characteris ti cs
P ower S u pp ly B a tt ery P owered
B a tt ery Ty p e C R 12 3 A x 1 ( included ) , 3V/ 1 6 00 m Ah
Ty p ical V oltage 3V
Consu mpti on
Ma x . current : 4 1. 57 m A
Q uiescent current : 2 7 . 5μ A
Low B a tt ery Level 2. 45 V
S tandard B a tt ery Li f e 5 Y ears
General
Op era ti on Te mp erature - 10 °C to 55 °C ( 1 4 ° F to 1 3 1 ° F)
S torage Te mp erature - 20 °C to 6 0 °C (-4 ° F to 1 4 0 ° F)
Op era ti on Hu m idity 10% to 9 0%
Di m ension (Wx H x D )
22. 5mm × 10 3mm × 2 3 .2 mm
1 3mm × 34 . 4mm × 11. 4mm
W eight 59 g
A pp lica ti on S cenario I ndoor