background image

Tri-pod Turnstile • User Manual 

 

18 

4.2 Tips and trouble shooting 

Q1:When access board send open sigal,arm move reverse and indicator show reverse? 
Reasons:open signal reverse connection 
Solotion:exchange SW1 GND and SW2 GND terminal of board. 
 
Q2: Indicator is not working? 
Reasons:1. wires loose 2.indicator or board damage 
Solution:1.Check connect wire of indicator   
2.Repalce indicator or board. 
 
Q3: How to achieve free for one way ? 
1.

 

Remove one of square solenoid 

 

Q4: Arm can not push when swipe card and indicator show green ? 
Solution: 1.Check 24V GND output for square solenoid 2.Replace new board or solenoid 

 

Q5: Passing two or three people after swipe card at a time.   
Reasons:   
1. The Positon sensor didn’t be touched by the right screw cap when the turn plate rotating. (Or 
didn’t receive the effective signal even touched) 
2.

 

The square solenoid does not stretch smoothly. 

3.

 

Control baord damage  

Solution:   
1.Move the position senor inward ,Check connect wires to board 
2.

 

Adjust square solenoid or replace new one. 

3. Changing the square electromagnet. 
4. Replace a new board. 
Q6:Didn’t drop arm automatically when power failure 
Reasons: The drop arm device is putting too high so that the solenoid attracts plate, which button 
can not press arm lock parts. 
Solution: Firstly, adjusting drop arm device upper by hand, making the solenoid attract plate, then 
unscrew the four screws on the drop arm device and press them down (normally attach the arm 
lock parts is ok),at last , tightening the screw and circle dropout test. 
 
Q7:The arm won’t operate when power on. 
Reasons:   
1. The drop arm device is putting too high, raising the arm up by manual, but arm lock will push 
drop arm device bottom, but solenoid can’t reach to the position which attract plate. 
2.The  drop  arm  device  is  putting  too  low,  raising  the  arm  up  by  manual,  the  arm  lock  will  push 
drop  arm  device  bottom,  after  solenoid  attract  plate,  the  arm  haven’t  be  fixed  to  the  balance 
position, so the bottom of drop arm device pressed the arm lock ,can’t be closed. 

Summary of Contents for DS-K3G4402 Series






















Reviews: