Regulatory Information
FCC Informa on
Please take a en on that changes or modifica on not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protec on against harmful interference in a residen al installa on. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruc ons, may cause harmful interference to radio
communica ons. However, there is no guarantee that interference will not occur in a
par cular installa on. If this equipment does cause harmful interference to radio or
television recep on, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separa on between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between
the radiator and your body.
FCC Condi ons
This device complies with part 15 of the FCC Rules. Opera on is subject to the following two
condi ons:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired opera on.
2006/66/EC (ba ery direc ve): This product contains a ba ery that cannot
be disposed of as unsorted municipal waste in the European Union. See
the product documenta on for specific ba ery informa on. The ba ery is
marked with this symbol, which may include le ering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the ba ery to
your supplier or to a designated collec on point. For more informa on see:
www.recyclethis.info
2012/19/EU (WEEE direc ve): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For
proper recycling, return this product to your local supplier upon the
purchase of equivalent new equipment, or dispose of it at designated
collec on points. For more informa on see: www.recyclethis.info
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the RE Direc ve 2014/53/EU, the EMC Direc ve
2014/30/EU, the RoHS Direc ve 2011/65/EU.
Warning
In the use of the product, you must be in strict compliance with the electrical safety
regula ons
of the na on and region.
CAUTION: To reduce the risk of fire, replace only with the same type and ra ng of fuse.
CAUTION: This equipment is for use only with Hikvision’s bracket. Use with other (carts,
stands, or carriers) may result in instability causing injury.
To prevent possible hearing damage, do not listen at high volume levels for long periods.
Please use the power adapter, which is provided by normal company. The power
consump on cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause over-
heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the device.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the
power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service
center. Never a empt to disassemble the device yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)
Cau on
+
iden fies the posi ve terminal(s) of equipment which is used with, or generates
direct current. + iden fies the nega ve terminal(s) of equipment which is used with,
or generates direct current.
No naked flame sources, such as lighted candles, should be placed on the equipment.
The USB port of the equipment is used for connec ng to a USB flash drive only.
The serial port of the equipment is used for debugging only.
Burned fingers when handling
. Wait one-half hour a er
the fingerprint sensor metal
switching off before handling the parts.
Install the equipment according to the instruc ons in this manual.
To prevent injury, this equipment must be securely a ached to the floor/wall in
accordance with the installa on instruc ons.
Do not drop the device or subject it to physical shock, and do not expose it to high
electromagne sm radia on. Avoid the equipment installa on on vibra ons surface or
places subject to shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the specifica on of the device for
the detailed opera ng temperature), cold, dusty or damp loca ons, and do not expose
it to high electromagne c radia on.
The device cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ven la on or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the device at the sun or extra bright places. A blooming or smear may
occur otherwise (which is not a malfunc on however), and affec ng the endurance of
sensor at the same me.
Please use the provided glove when open up the device cover, avoid direct contact
with the device cover, because the acidic sweat of the fingers may erode the surface
coa ng of the device cover.
Please use a so and dry cloth when clean inside and outside surfaces of the device
cover, do not use alkaline detergents.
Please keep all wrappers a er unpack them for future use. In case of any failure
occurred, you need to return the device to the factory with the original wrapper.
Transporta on without the original wrapper may result in damage on the device and
lead to addi onal costs.
Improper use or replacement of the ba ery may result in hazard of explosion. Replace
with the
same or equivalent type only. Dispose of used ba eries according to the instruc ons
provided by the ba ery manufacturer.
Biometric recogni on products are not 100% applicable to an -spoofing
environments. If you require a higher security level, use mul ple authen ca on
modes.
Please make sure that the biometric recogni on accuracy will be affected by the
collected pictures' quality and the light in the environment, which cannot be 100%
correct.
Recommended: Use other authen ca on methods if the device if
affected by the light or other items.
1:N Matching:
The device will compare the captured face picture with
the ones in the database.
Biometric recogni on products are not 100%
applicable to an -spoofing environments. If you
require a higher security level, use mul ple
authen ca on modes.
4
Adding Face Information
Correct
Tilt
Raise
Side
Bow
Tips When Collec ng/Comparing Face Picture
Expression
Keep
your
expression
naturally
when
collec ng
or
comparing
face
pictures
,
just
like
the
expression
in
the
picture
on
the
right
.
Posture
In
order to get a good quality and accurate face
picture
,
posi on
your
face
looking
at
the
camera
when
collec ng
or
comparing
face
picture.
Size
Make sure your face is in the middle of the collec ng window.
Do not wear hat, sunglasses, or other accessories that can affect the facial
recogni on func on.
Do
not
make
your
hair
cover
your
eyes, ears, etc. and heavy makeup is
not allowed.
Correct
Too Far
Too Close
Posi ons When Collec ng/Comparing Face Picture
Recommended Height:
1.43 m to 1.90 m
Too High
Too Low
Too Far
Too Close
0.5 m
1.2 m
0.5 m
0.5 m
1.4 m
1.4 m
1.4 m
1.4 m
1. Use finger to hold the screen surface for 3 s and slide to right/le
and enter the ac va on password to enter the Home page.
2. Enter the User Management page, tap + to enter the Add User
page.
3. Set the user parameters according to actual needs.
Only the device with the fingerprint module support the
fingerprint related func ons.
Y4. Tap Face and add the face informa on according to the
instruc ons.
You can view the captured picture on the screen, Make sure the face
picture is in good quality and size.
For details about the ps and posi ons when collec ng or comparing
the face picture, see the contents on the right.
5. If the picture is in good condi on, tap the .
Or tap the to take another face picture.
6. Tap the save icon to save the se ngs.
Go back to the ini al page to start authen ca on.
For other authen ca on methods, see the device user manual.
3
Activation
Activate via Device
Power on and wire the network cable a er installa on. You
should ac vate the device before the first login.
If the device is not ac vated yet, it will enter the Ac vate
Device page a er powering on.
1. Create a password and confirm the password.
Note:
admin or nimda are not supported.
2. Tap
Ac vate
to ac vate the device.
Note:
For other ac va on methods, see the device user manual.
3. Set applica on mode and recogni on mode by following
the instruc ons according to your actual needs.
We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case le ers, lower case le ers,
numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password
monthly or weekly can be er protect your product.
Step
:
Use only power supplied listed in the user instruc ons:
Scan
the
QR
code
to
get
the
user
manual
for
detailed
informa on
.
Note that mobile data charges may apply if Wi-Fi is unavailable.
ADS
-
26FSG-12 12018EPG
ADS
-
26FSG-12 12018EPI-01
ADS
-
26FSG-12 12018EPCU
ADS
-
26FSG-12 12018EPB
MSA-C1500IC12.0-18P-BR
MOSO Technology Co., Ltd.
Shenzhen Honor Electronic Co., Ltd.
Shenzhen Honor Electronic Co., Ltd.
Shenzhen Honor Electronic Co., Ltd.
Shenzhen Honor Electronic Co., Ltd.
PG
PI
PCU
PB
PBR
Standard
Manufacturer
Model
Set Applica on Mode
A er
ac va on
,
you
should
select
an
applica on
mode
.
Select
Indoor
or
Others
from the drop-down list and tap OK.
If you install the device indoors near the window or
the face recogni on func on is note working well,
select
Others
.
Set Administrator
Steps:
1. Enter the administrator’s name and tap
Next
.
2. Select a creden al to add. You can select face, fingerprint,
or card.
3. Tap
OK
.
Set Language
Select a language from the drop-down list.
120 mm
