manualshive.com logo in svg

HIKVISION DS-3WR12C, User Manual, Page: 69 / 147

Share
Download
HIKVISION DS-3WR12C User Manual Download Page 69

WiFi Router • User Guide 

61 

IPv6 configuration 

This router supports IPv4 and IPv6 dual-stack protocols. In the IPv6 part, you can: 

-

 

Connect to the IPv6 network of ISPs

 

-

 

Change IPv6 LAN settings

 

-

 

View IPv6 connection status

 

The router can access the IPv6 network of ISPs through three connection types. Choose the 
connection type by referring to the following chart. 

 

IPv6 connection type 

IPv6 service is included in the PPPoE user name and password. 

PPPoEv6

 

 

The ISP does not provide any PPPoEv6 user name and password. 

 

The ISP does not provide information about the IPv6 address. 

 

You have a router that can access the IPv6 network. 

DHCPv6

 

The ISP provides you with such information as IPv6 address, subnet 
mask, default gateway and DNS server. 

Static IPv6

 

 

 

Before configuring the IPv6 function, please ensure that you are within the coverage of the IPv6 
network and already subscribe to the IPv6 internet service. Contact your ISP for any doubt about it. 

 

 

Scenario 

Connection Type 

Summary of Contents for DS-3WR12C




















































































































































Reviews:

No comments