manualshive.com logo in svg

HIKVISION DS-3WR12C, User Manual, Page: 72 / 147

Share
Download
HIKVISION DS-3WR12C User Manual Download Page 72

WiFi Router • User Guide 

64 

IPv6 network test: 

Launch a web browser on a phone or a computer that is connected to the router, and visit 

test-

ipv6.com

. The website will test your IPv6 connection status. 

When "You have IPv6" is shown on the page, it indicates that the configurations succeed and you 
can access IPv6 services. 

 

 

Test your IPv6 connectivity 

If the IPv6 network test fails, try the following solutions: 

-

 

Navigate to the 

Route Settings

 > 

IPv6 Configuration

 > 

IPv6 Status

, ensure that the IPv6 WAN 

address is a global unicast address. 

-

 

Ensure that devices connected to the router obtain their IPv6 address through DHCPv6. 

-

 

Consult your ISP. 

DHCPv6 

DHCPv6 enables the router to obtain IPv6 address from the DHCPv6 server to access the internet, 
which is applicable in the following scenarios: 

-

 

The ISP does not provide any PPPoEv6 user name and password. 

-

 

The ISP does not provide information about the IPv6 address. 

-

 

You have a router that can access the IPv6 network. 

 

 

Summary of Contents for DS-3WR12C




















































































































































Reviews:

No comments