HIKVISION DS-2CE71D8T-PIRL User Manual Download Page 2

Regulatory Information 
FCC Information 
Please take attention that changes or modification not 
expressly approved by the party responsible for 

compliance could void the user’s authority to operate 
the equipment. 
FCC compliance: This equipment has been tested and 

found to comply with the limits for a Class A digital 
device, pursuant to part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection 

against harmful interference when the equipment is 

operated in a commercial environment. This equipment 
generates, uses, and can radiate radio frequency energy 

and, if not installed and used in accordance with the 

instruction manual, may cause harmful interference to 
radio communications. Operation of this equipment in a 

residential area is likely to cause harmful interference in 

which case the user will be required to correct the 
interference at his own expense. 
FCC Conditions 
This device complies with part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 
1. This device may not cause harmful interference. 

2. This device must accept any interference received, 

including interference that may cause undesired 
operation. 
 
EU Conformity Statement 

This product and - if applicable - the 

supplied accessories too are marked with 

"CE" and comply therefore with the 
applicable harmonized European 

standards listed under the Low Voltage Directive 

2014/35/EU, the EMC Directive 2014/30/EU, the RoHS 
Directive 2011/65/EU. 

2012/19/EU (WEEE directive): Products 

marked with this symbol cannot be 

disposed of as unsorted municipal waste in 
the European Union. For proper recycling, 

return this product to your local supplier 
upon the purchase of equivalent new 

equipment, or dispose of it at designated collection 

points. For more information see: www.recyclethis.info. 

2006/66/EC (battery directive): This product contains 

a battery that cannot be disposed of as 

unsorted municipal waste in the European 
Union. See the product documentation for 
specific battery information. The battery is 

marked with this symbol, which may 

include lettering to indicate cadmium (Cd), lead (Pb), 
or mercury (Hg). For proper recycling, return the 

battery to your supplier or to a designated collection 
point. For more information see: 
www.recyclethis.info. 

 

Industry Canada ICES-003 Compliance 
This device meets the CAN ICES-3 (A)/NMB-3(A) 
standards requirements. 

 

Warning 
This is a class A product. In a domestic environment this 

product may cause radio interference in which case the 
user may be required to take adequate measures. 

 

Summary of Contents for DS-2CE71D8T-PIRL















Reviews: