background image

UM DS-2CE1xU8T-ITx 042618NA 

1.1.2

 

FCC Conditions 

This device complies with part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 

1.

 

This device may not cause harmful interference. 

2.

 

This device must accept any interference received, 
including interference that may cause undesired 
operation. 

1.1.3

 

EU Conformity Statement 

This product and, if applicable, the 

        

supplied accessories too are marked with 
“CE” and comply therefore with the 
applicable harmonized European standards 
listed under the Low Voltage Directive 
2014/35/EU, the EMC Directive 

2012/19/EU (WEEE Directive): Products 
marked with this symbol cannot be 
disposed of as unsorted municipal waste in 
the European Union. For proper recycling, 
return this product to your local supplier 
upon the purchase of equivalent new 
equipment, or dispose of it at designated 
collection points. For more information see: 
www.recyclethis.info. 

2006/66/EC (Battery Directive): This 
product contains a battery that cannot be 
disposed of as unsorted municipal waste in 
the European Union. See the product 
documentation for specific battery 
information. The battery is marked with this 
symbol, which may include lettering to 
indicate cadmium (Cd), lead (Pb), or 
mercury (Hg). For proper recycling, return 
the battery to your supplier or to a 
designated collection point. For more 
information see: www.recyclethis.info. 

1.1.4

 

Industry Canada ICES-003 Compliance 

This device meets the CAN ICES-3 (A)/NMB-3(A) 
standards requirements. 

1.1.5

 

Safety Instruction 

These instructions are intended to ensure that the 
user can use the product correctly to avoid danger or 
property loss. 

The precaution measure is divided into “Warnings” 
and “Cautions.” 

Warnings: 

Serious injury or death may occur if any of 

the warnings are neglected. 

Cautions: 

Injury or equipment damage may occur if 

any of the cautions are neglected. 

 

 

Warnings 

Follow these 

safeguards to prevent 
serious injury or death. 

Cautions 

Follow these 

precautions to prevent 
potential injury or 
material damage. 

 

Summary of Contents for DS-2CE17U8T-IT

















Reviews: