HIKVISION DS-2CE10KF0T-FS User Manual Download Page 4

 
Safety Instruction 
These instructions are intended to ensure that user can 
use the product correctly to avoid danger or property 
loss.   
The precaution measure is divided into “Warnings” and 
“Cautions”. 
Warnings: Serious injury or death may occur if any of 
the warnings are neglected. 
Cautions: Injury or equipment damage may occur if any 
of the cautions are neglected. 

  Warnings 

 

In the use of the product, you must be in strict 
compliance with the electrical safety regulations of 

the nation and region. 

 

Input voltage should meet both the SELV (Safety Extra 
Low Voltage) and the Limited Power Source with 12 

VDC according to the IEC60950-1 and IEC62368-1 

standard. Refer to technical specifications for detailed 
information. 

 

The socket-outlet shall be installed near the 

equipment and shall be easily accessible. 

 

An all-pole mains switch shall be incorporated in the 

electrical installation of the building. 

 

Do not connect multiple devices to one power 
adapter to avoid over-heating or a fire hazard caused 
by overload. 

 

Make sure that the plug is firmly connected to the 
power socket. 

 

If smoke, odor or noise rise from the device, turn off 

the power at once and unplug the power cord, and 
then contact the service center.   

 

Never attempt to disassemble the camera by 

unprofessional personal. 

  Cautions 

 

No naked flame sources, such as lighted candles, 
should be placed on the equipment. 

 

Install the equipment according to the instructions in 
this manual. 

 

To prevent injury, this equipment must be securely 
attached to the floor/wall in accordance with the 
installation instructions. 

 

Do not drop the camera or subject it to physical 
shock. 

 

Do not touch senor modules with fingers. 

 

Do not place the camera in extremely hot, cold (the 
operating temperature shall be -40°C to 60°C), dusty 
or damp locations, and do not expose it to high 
electromagnetic radiation. 

 

If cleaning is necessary, use clean cloth with a bit of 
ethanol and wipe it gently.   

 

 

Warnings Follow 
these safeguards to 
prevent serious injury 
or death. 

Cautions Follow these 
precautions to prevent 
potential injury or 
material damage.   

Summary of Contents for DS-2CE10KF0T-FS
















Reviews: