Hangzhou Hikvision Digital Technology CO.,Ltd.
No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
E N G L I S H
1
2
3
Specification
Appearance
Note: Power down the control panel before installation and wiring.
1. Loosen the screws and open the case.
2. Take out the upper main board.
3. Take out the lower main board.
4. Fix the rear case on the wall.
5. Install the lower main board and the loudspeaker.
6. (Wiring before install the upper main board.)
Install the upper main board.
7. Connect the power supply and turn on the switch.
8. Close the case and tighten the screws.
1
Set Up
User Manual
Installation and Wiring
AX PRO M2H
Quick Start Guide
2
3
4
UD25504B-B
1. Main Board
4. Battery
5. Antenna Position
6. Loudspeaker
2. Power Switch
3. Tamper Switch
1.Add the AX PRO to Hik-ProConnect or Hik-Connect APP.
2.Enroll the peripheral to the AX PRO.
1
1
2
3
4
6
7
8
5
2
xxxx
OR
POWER ON
TRIGGER
Add Device
Sites:xxx
My Device
OR
Hik-Connect
Hik-ProConnect
1
5
6
2
3
4
power
Z1
Z3
Z5
Z7
Z9
Z11
Z13
Z15
Z2
Z4
Z6
Z8
Z10
Z12
Z14
Z16
- AUX +
COM
COM
COM
COM
COM
COM
COM
COM
SMOKE
DETECTOR
-EXT+ PGM1 C1 PGM2 C2
DOUBLE
ZONE
OUTPUT
CONTROL
SEOL
DEOL
4 User Manual
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation
Basic
User
Software
Communication
Hardware
Others
RF frequency
433 Mhz
48
6
8 (Including Tag reader)
4
48
Up to 96 (Single), up to 5 (Multi)
4
1, 120, 46
32
Wired network, Wi-Fi, 3/4G on board
Dual
100 to 240V~, 50/60 Hz, 0.66A to 0.3A
-10 °C to 40 °C
261 mm × 199 mm × 86.4 mm
1083g (No battery)
Arm/Disarm, Alarm, Alert, Cloud, Power
Hik-Connect/Hik-ProConnect/Web
Portal/ IVMS4200/ Convergence Cloud
SIA DC09 (SIA level 2, Contact ID), ISUP,
ISAPI (SDK), CSV-IP, FSK Module
Hik-IP Receiver & Hik-IP Receiver Pro
(Sur-Gard & Ademco 685)
Supports video verification and remote
control
12v 7Ah storage battery (sold
separately), up to 36 hours
Alarm&abnormal (3000), user operation
(1500), user management (200)
Up to 96 (including 48 PIRCAMs & 16
onboard Wired Zones & onboard Wired
Outputs)
Keyfob
Wireless sounder
Keypad
Wireless repeater
Tag
Zone
Transmitter
Onboard video clip
Admin, installer, user
Area
LEDs indication
Memory Log stored
Programming tool
Network
ARC protocol
SIM slot
Power supply
Battery type
Operation temperature
Dimension (W×H×D)
Weight
Please pull the antenna cable
carefully to prevent damage.