HIKOKI G10SK3, Handling Instructions Manual

Page: 7 / 24

English
7
6. To prolong the life of the machine and ensure a fi rst
class fi nish, it is important that the machine should not
be overloaded by applying too much pressure. In most
applications, the weight of the machine alone is su ffi cient
for e ff ective grinding. Too much pressure will result in
reduced rotational speed, inferior surface fi nish, and
overloading which could reduce the life of the machine.
7. The wheel continues to rotate after the tool is switched
o ff .
After switching o ff the machine, do not put it down until the
depressed center wheel has come to a complete stop.
Apart from avoiding serious accidents, this precaution
will reduce the amount of dust and swarf sucked into the
machine.
SPECIFICATIONS
Model PDA-100K G10SK3
Power Source (by areas) *1 (110V, 220V, 230V, 240V) 50/60 Hz (110V, 220V, 230V) 50/60 Hz
Power Input *1 705 W
No-load speed 12,000/min
Max. Peripheral Speed 72 m/s (4300 m/min)
Wheel size
external dia. 100 mm
thickness 4 mm, 6 mm
hole dia. 16 mm
Weight (Only main body) 1.5 kg 1.4 kg
*1
Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Depressed center wheel (excluding Taiwan) ................1
(Resinoid Wheel)
external dia. 100 mm
thickness 4 mm
hole dia. 16 mm
(2) Wrench .........................................................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES . . . . sold separately
CAUTION
Always operate the grinder with the wheel guard
attached.
1. 100mm Sanding Disc Set
Washer Nut
Sanding Disc
Rubber Pad
Washer
In case when only a relatively small metal surface area is
to be polished and it is desired to give it a particularly fi ne
fi nish, this is used for preliminary polishing of the metal
surface before applying point, for removing rust, and for
removing point when a new test is to be applied.
There are eleven di ff erent kinds of sanding discs, having
grains of #16, #20, #24, #30, #36, #40, #50, #60, #80,
#100, #120. When placing your order, please specify the
grain of the disc desired.
2. Diamond Wheel Set
This is used for cutting and scribing of concrete, stone,
tile etc.
Guide Base Ass’y
Diamond Wheel
Segment
Type
Optional accessories are subject to change without notice.
APPLICATIONS
○ Removal of casting fi n and fi nishing of various types of
steel, bronze and aluminum materials and castings.
○ Grinding of welded sections or sections cut by means of
a cutting torch.
○ Grinding of brick, marble, etc.
○ Cutting and scribing of concrete, stone, tile, (use the
diamond wheel)
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements speci fi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
8. When the machine is not use, the power source should
be disconnected.
9. Be sure to switch OFF and disconnect the attachment
plug from the receptacle to avoid a serious accident
before the depressed center wheel is assembling and
disassembling.
10. RCD
The use of a residual current device with a rated residual
current of 30 mA or less at all times is recommended.
000Book̲PDA-100K̲Asia.indb 7 000Book̲PDA-100K̲Asia.indb 7 2021/02/02 13:59:37 2021/02/02 13:59:37