background image

11

10. When working at elevated locations, clear the area of 

other people and aware of conditions below you.

11. Always charge the battery at a temperature of 0°C–40°C. 

A temperature of less than 0°C will result in over charging 

which is dangerous. The battery cannot be charged at a 

temperature higher than 40°C. 

  The most suitable temperature for charging is that of 

20°C–25°C.

12. Do not use the charger continuously.

 

When one charging is completed, leave the charger for 

about 15 minutes before the next charging of battery.

13. Do not allow foreign matter to enter the hole for 

connecting the rechargeable battery.

14. Never disassemble the rechargeable battery and 

charger.

15. 

Never short-circuit the rechargeable battery. 

Shortcircuiting the battery will cause a great electric 

current and overheat. It results in burn or damage to the 

battery.

16. Do not dispose of the battery in 

fi

 re. If the battery is burnt, 

it may explode.

17. Bring the battery to the shop from which it was purchased 

as soon as the post-charging battery life becomes too 

short for practical use. Do not dispose of the exhausted 

battery.

18. Do not insert object into the air ventilation slots of the 

charger. Inserting metal objects or in

fl

 ammables into the 

charger air ventilation slots will result in electrical shock 

hazard or damaged charger.

19. When using this unit continuously, the unit may overheat, 

leading to damage in the motor and switch. Therefore, 

whenever the housing becomes hot, give the tool a 

break for a while.

20. Make sure that the battery is installed 

fi

 rmly. If it is at all 

loose it could come o

  and cause an accident.

21. Do not use the product if the tool or the battery terminals 

(battery mount) are deformed.

  Installing the battery could cause a short circuit that 

could result in smoke emission or ignition.

22. Keep the tool’s terminals (battery mount) free of swarf 

and dust.

  Prior to use, make sure that swarf and dust have not 

collected in the area of the terminals.

  During use, try to avoid swarf or dust on the tool from 

falling on the battery.

  When suspending operation or after use, do not leave 

the tool in an area where it may be exposed to falling 

swarf or dust.

 

Doing so could cause a short circuit that could result in 

smoke emission or ignition.

23. Always use the tool and battery at temperatures between 

-5°C and 40°C.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the 

protection function to stop the output.

In the cases of 1 to 3 described below, when using this 

product, even if you are pulling the switch, the motor may 

stop. This is not the trouble but the result of protection 

function.

1.  When the battery power remaining runs out, the motor 

stops.

 

In such a case, charge it up immediately.

2.  If the tool is overloaded, the motor may stop. In this 

case, release the switch of tool and eliminate causes of 

overloading. After that, you can use it again.

3.  If the battery is overheated under overload work, the 

battery power may stop.

  In this case, stop using the battery and let the battery 

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation, 

smoke emission, explosion and ignition beforehand, please 

be sure to heed the following precautions.

1.  Make sure that swarf and dust do not collect on the 

battery.

  During work make sure that swarf and dust do not fall on 

the battery.

  Make sure that any swarf and dust falling on the power 

tool during work do not collect on the battery.

  Do not store an unused battery in a location exposed to 

swarf and dust.

  Before storing a battery, remove any swarf and dust that 

may adhere to it and do not store it together with metal 

parts (screws, nails, etc.).

2.  Do not pierce battery with a sharp object such as a 

nail, strike with a hammer, step on, throw or subject the 

battery to severe physical shock.

3.  Do not use an apparently damaged or deformed battery.

4.  Do not use the battery for a purpose other than those 

speci

fi

 ed.

5.  If the battery charging fails to complete even when a 

speci

fi

 ed recharging time has elapsed, immediately stop 

further recharging.

6.  Do not put or subject the battery to high temperatures or 

high pressure such as into a microwave oven, dryer, or 

high pressure container.

7.  Keep away from 

fi

 re immediately when leakage or foul 

odor are detected.

8.  Do not use in a location where strong static electricity 

generates.

9.  If there is battery leakage, foul odor, heat generated, 

discolored or deformed, or in any way appears abnormal 

during use, recharging or storage, immediately remove it 

from the equipment or battery charger, and stop use.

10. Do not immerse the battery or allow any 

fl

 uids  to 

fl

 ow 

inside. Conductive liquid ingress, such as water, can 

cause damage resulting in 

fi

 re or explosion. Store your 

battery in a cool, dry place, away from combustible and 

fl

 ammable items. Corrosive gas atmospheres must be 

avoided.

CAUTION

1.  If liquid leaking from the battery gets into your eyes, 

do not rub your eyes and wash them well with fresh 

clean water such as tap water and contact a doctor 

immediately.

 

If left untreated, the liquid may cause eye-problems.

2.  If liquid leaks onto your skin or clothes, wash well with 

clean water such as tap water immediately.

 

There is a possibility that this can cause skin irritation.

3. If you 

fi

 nd rust, foul odor, overheating, discolor, 

deformation, and/or other irregularities when using the 

battery for the 

fi

 rst time, do not use and return it to your 

supplier or vendor.

WARNING

If a conductive foreign matter enters in the terminal of lithium 

ion battery, the battery may be shorted, causing 

fi

 re. When 

storing the lithium ion battery, obey surely the rules of 

following contents.

  Do not place conductive debris, nail and wires such as 

iron wire and copper wire in the storage case.

  To prevent shorting from occurring, load the battery in 

the tool or insert securely the battery cover for storing 

until the ventilator is not seen.

00Book̲G3613DVE̲Aust.indb   11

00Book̲G3613DVE̲Aust.indb   11

2022/08/26   15:06:35

2022/08/26   15:06:35

Summary of Contents for G 3613DVE

























Reviews: