Hifonics Zeus Zxi 6408, User Manual

Page: 4 / 15

AMPLIFIER FEATURE DESCRIPTIONS
The
AMPLIFIER CH 3/CH 4 X-OVER slide switch select
s
the input signal for channel
pair 3&4
- Hi: Selects the built in HIGH PASS filter, varia
b
le from 10 Hz to 150Hz.
- FULL: Bypasses all crossovers for full frequency range operation.
- LP/BP:
Selects the built in
LOW PASS
filter, variable from 30 Hz to 150 Hz.
Note that the LOW PASS signal is
MONO.
- In the
LP/BP
position, the
HIGH PASS
filter acts as a subsonic filter.
- When the
LP/BP
mode is selected, a 0 to +10 dB, at 45 Hz,
BASS EQ
is also switched in.
- Full range signal from channels 1 / 2 inputs are routed to the
Line OUT RCA
jacks,
regardless of the setting of the
X-OVER
switches.
- The
REMOTE
jack enables dash mount level control of the LOW PASS signal, CH3/4 only.
2
ZXi6008 / ZXi1008 / ZXi1308 2 CHANNEL AMPLIFIERS
ZXi8008 5 CHANNEL AMPLIFIERS
ZXi4408 / ZXi6408 / ZXi8408 4 CHANNEL AMPLIFIERS
HFR - 3
MI N MAXX
BOOST
HP FULL LP/BP
10Hz 150Hz 30Hz 150Hz 0dB 10dB 6V 0.2V
REMOTE
HI PASS LOW PASS BASS EQ LEVEL POWER X-OVER
PROTECT
LINE INPUT
CH1
CH2
LINE OUT
L
R
LINE INPUT
REMOTE
POWER
PROTECT
LINE OUT
HI FULL LP/BP
HI FULL LP/BP
6V 0.2V 10Hz-150Hz 30Hz-150Hz 0dB-10dB
HI PASS LOW PASS BASS EQ LEVEL
X-OVER
1/2 CH
6V 0.2V 10Hz-150Hz 30Hz-150Hz 0dB-10dB
X-OVER
3/4 CH
HI PASS LOW PASS BASS EQ LEVEL
MODE
CH2-CH4
L
R
CH1
CH2
CH3
CH4
REMOTE
POWER
PROTECT
LINE INPUT
CH1
CH2
CH3
CH4
5CH
50Hz- 4Khz 50Hz- 150hz
HI PASS
HI FULL
X-OVER
1/2 CH
6V 0.2V
LEVEL
6V 0.2V
LEVEL LOW PASS
250Hz-4KHz
HI PASS
MODE
Ch2 Ch5
Ch4
HI-FULL BP
X-OVER
3/4 CH
0dB-10dB
BASS EQ
30Hz-150Hz
LOW PASS
6V 0.2V
LEVEL 5CH
ZEUS ZXi SERIES AMPLIFIERS
! ! Each model is capable of 4 & 2 ohms stereo per channel, or 4 ohms mono bridged Crossover filter slopes are 12 dB/octave for stereo filters, and 24 dB/octave for mono
operation. filters.
! ! A
POWER
LED indicates the powered “up” and turned “on” condition. Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all
!
All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short
bridgeable amplifiers.
! circuit, and amplifier DC faults indicated by the
DIAGNOSTIC, or PROTECT
LED. The input sensitivities for rated output powers are variable from 0.2 volt to 6 volt.
!
All crossovers are fully variable in their respective ranges.
The
X-OVER
slide switch selects the internal crossover functions:
- The input signal is routed directly to the
LINE OUT
RCA jacks, regardless of the
X-OVER
setting simplifying daisy chaining of amplifiers.
- HI:
Selects the built in
HIGH PASS
filter, variable from 10 Hz to 150Hz.
- FLAT:
Bypasses all crossovers for full frequency range operation.
LP/BP:
Selects the built in
LOW PASS
filter, variable from 30 Hz to 150 Hz.
Note that the LOW PASS signal is
MONO.
- In the
LP/BP
position, the
HIGH PASS
filter acts as a subsonic filter.
When the
LP/BP
mode is selected, a 0 to +10 dB, at 45 Hz,
BASS EQ
is also switched
in.
The
REMOTE
jack enables dash mount level control of the LOW PASS signal.
The
AMPLIFIER CH 1/2CH X-OVER
slide switch selects the input signal for channel
pair 1 & 2:
- HI:
Selects the built in
HIGH PASS
filter, variable from 10 Hz to 150Hz.
- FULL:
Bypasses all crossovers for full frequency range operation.
- LP/BP:
Selects the built in
LOW PASS
filter, variable from 30 Hz to 150Hz.
Note that the LOW PASS signal is
MONO:
- In the
LP/BP
position, the
HIGH PASS
filter acts as a subsonic filter.
- When the
LP/BP
mode is selected, a 0 to +10 dB, at 45 Hz,
BASS EQ
is also switched
in.
The ZXi8006 has three sets of inputs:
Line inputs on RCA jacks for channel pairs 1&2, 3&4, and MONO channel 5. These inputs
can be used in various combinations, to suit the application, depending on the settings of
the INPUT MODE switch, and the X-OVER switches for channels 1&2, and channels 3&4,
respectively.
INPUT MODE
slide switch:
- In the
CH2
position, ALL five amplifier inputs are selected from the CH1/CH2 RCA jacks.
Channel 5 receives a mono mixed signal.
- In the
4CH
position, channel pair 1&2 receive input signal from RCA jacks CH1 and CH2,
and channel pair 3&4 receive input signal from RCA jacks CH3 and CH4. A mono mixed
signal from these four RCA jacks are also fed to channel 5.
- When
5CH DISCRETE
is selected, each channel receives an input signal from its
respective input RCA jack. Channel 5 has two jacks on its LINE INPUT, which are summed
together.
CH1/2 X-OVER slide switch:
FULL: Sets this pair to full range operation.
HP: Selects the built in HIGH PASS filter, variabl
e
from 50 Hz to 4 KHz.
CH3/4 X-OVER
slide switch:
- FULL:
Sets this pair to full range operation.
- B.P. :
In this mode, the HIGH PASS ranges from 50Hz to 150Hz and the LOW
PASS filter ranges from 250Hz to 4KHz, are selected to form a BANDPASS
c r o s s o v e r f i l t e r.
- HP:
Selects the HIGH PASS filter, variable from 50Hz to 4KHz.
CH 5:
- The channel 5 functions were chosen to be very specific to mono bass operation, and not
switchable:
- The
LOW PASS
filter has a variable range from 30 Hz to 150 Hz.
- The
BASS EQ
gives a bass boost, 0 to +10 dB, at 45 Hz.