25
SPECIFICATIONS
|ENG
MODEL
CHANNELS
CIRCUIT
OUTPUT POWER RMS 13,8 V
Watts @ 4 Ohms
Watts @ 2 Ohms
Watts @ 4 Ohms mono bridged
OUTPUT POWER MAX. 13,8 V
Watts @ 4 Ohms
Watts @ 2 Ohms
Watts @ 4 Ohms mono bridged
Frequency Range –3dB
Damping Factor
Signal-to-Noise Ratio
Channel Separation
THD&N
Input Sensitivity
Input Impedance
CH 1 & CH 2
X-Over Modes
Various Highpassfilter
CH 3 & CH 4
X-Over Modes
Various Highpassfilter
Various Lowpassfilter
Bass Boost @ 50 Hz
Bass Remote
Line Outputs (RCA)
Fuse Ratings
Dimensions
Width x Height x Length
TSi600-IV
4
CLASS A/B Analog
4 x 80
4 x 125
2 x 250
4 x 160
4 x 250
2 x 500
20Hz - 30 kHz
> 400
> 90 dB
> 60 dB
0,05%
6 - 0.2 V
> 47 kOhm
DUPE - HPF - Full
10 - 1200 Hz
LPF/BPF - HPF - Full
10 - 1200 Hz
30 - 150 Hz
0 - 12 dB
BLC-TSi
Fullrange
2 x 35 A
220 x 55 x 300/365 mm
Technical specifications are subject to
change! Errors are reserved!
For damages on the vehicle and the
device, caused by handling errors of the
device, we can’t assume liability.
All HiFonics Amplifiers are tagged with
a individual serialnumber, which will be
registerd for statistic and service
conditional purposes.
All HiFonics Amplifiers are tagged with
a CE-Certification Mark. Thereby these
devices are ceritified for a use inside
vehicles inside the European Union (EU).
WARRANTY DISCLAIMER
The limited warranty comply with legal
regulations. Failures or damages caused
by overload, improper use or by using
the product for competitions are not
covered by the warranty.
Please return the defective product only
with a valid proof of purchase and a
detailed malfunction description.
TSi800-IV
4
CLASS A/B Analog
4 x 110
4 x 175
2 x 350
4 x 220
4 x 350
2 x 700
20Hz - 30 kHz
> 400
> 90 dB
> 60 dB
0,05%
6 - 0.2 V
> 47 kOhm
DUPE - HPF - Full
10 - 1200 Hz
LPF/BPF - HPF - Full
10 - 1200 Hz
30 - 150 Hz
0 - 12 dB
BLC-TSi
Fullrange
3 x 30 A
220 x 55 x 380/445 mm
You can simplify the installation of the high level speaker connections, if you use the separately available hi-to-lo adaptors
HF-HLA from HiFonics. You may find the adaptor at your car audio retailer.
With the HF-HLA you just need to connect the bared speaker cables in the regarding ports and connect the RCA jacks with LINE IN on
the amplifier.
Please ensure the correct polarity of the connections.
Usually the ”+” positive cables are red or dark grey,
With one HF-HLA adaptor you are able to connect one channel pair,
this means for a 4-channel amplfier you need two adaptors.
OPTIONAL ACCESSORIES FOR HiFONICS TITAN TSi AMPLIFIERS
R
Speaker Cables
+
To the LINE IN on the Amp
–
–
+
L
Summary of Contents for Titan TSi600-IV
Page 11: ...11 NOTIZEN DE...
Page 24: ...24 ENG NOTES...
