HIDRIA 0318-4-1005 Installation & Maintenance Download Page 2

USER'S GUIDE R18 AXIAL FAN , Iss: 6.05.2021

01

SAFETY

&

When unpacking the unit, grip the motor housing and lift it out very gently and carefully. Shocks
have to be avoided by all means! Wear safety shoes and cut-resistant gloves.
This appliance should only be installed or opened by qualified personnel.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children shall not play with the appliance. 

Cleaning and user maintenance shall not be made by children without supervision.
This appliance is solely intended as a built-in component and should not be operated otherwise.
Sufficient protection against accidental contact according to machinery directive 2006/42/CE has
to be safeguarded, especially for the rotating parts. Should there be a malfunction, it still has to
be safeguarded that the parts breaking off or flying away cannot cause serious damage or bodily
harm. 
Do not operate this appliance in an explosive atmosphere!
Fan must be fixed to stationary housing with appropriate screws according to this guide.
This appliance is not intended to be built as a partition fan.
The electrical connection must correspond to this installation guide and enclosed connecting
diagram as desribed in chapter 4. INSTALLATION AND CONNECTION - page 6 of this
document.
Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring
rules.
When connecting the unit to the power supply, dangerous voltages occur. Do not open the unit
within the first 5 minutes after disconnection from the power supply. Be sure that the unit is being
isolated.
Parallel operation of several units can cause dangerous charges of >50

µ

C between AC line

terminals and PE after disconnection.
With control voltage fed, the motor will restart automatically after a power failure.
The risk of pulling into rotating part. Do not wear any loose clothing (e.g. tie) or jewellery.
Long hair must be protected with a cap. Risk of injury!

The electronics housing can get hot.
In case the external metal enclosure is accessible to user, maximum operating ambient
temperature is reduced to max.amb. 55°C.

© Copyright  HIDRIA d.o.o., All rights reserved. Document is subject to change without prior notification.

2 / 10

Summary of Contents for 0318-4-1005











Reviews: