background image

INSTALLATION, MAINTENANCE AND USER'S GUIDE

FAN WITH ELECTRONICALLY COMMUTATED EXTERNAL-ROTOR MOTOR

Fan Code:

0318-4-1005

Fan type : R18R-080MPS-ET120B-01A01

&

Note :

Table of Contents :

01

SAFETY

02

TYPICAL FEATURES AND PROPER USE

03

OPERATING CONDITIONS

04

INSTALLATION AND CONNECTION

05

SPEED CONTROL

06

PUTTING INTO OPERATION

07

DIAGNOSTICS & TROUBLESHOOTING

08

PROTECTIVE FEATURES

09

MAINTENANCE, SERVICE AND CLEANING

10

TRANSPORT AND STORAGE

11

ErP, ROHS AND EMC DIRECTIVES

12

SERVICE ADDRESSES AND ADDITIONAL DATA

This document contains instructions and information for the operation, installation, connection, use and maintenance of
the product. Be sure to familiarize yourself with these instructions before working on this unit. Not paying attention to
these warnings and instructions may lead to malfunctions and failures or may seriously endanger human life. More
detailed information and instructions are available from the manufacturer on request.

Symbols :

WARNING - to indicate warning situation 

WARNING - to indicate hot surfaces

DANGER due to electric shock

NOTE - indicate valuable information

Summary of Contents for 0318-4-1005











Reviews: