background image

June 2016 

Page 23 of 25 

 

 

 

OMNIKEY 5121 Ethernet Encoder User Guide, L001436, Rev. 2.0 

3.6

 

OMNIKEY 5121 Ethernet Encoder Slot Management 

The OMNIKEY 5121 Ethernet Encoder device supports two slots: 

1.

 

Contact Reader Slot. 

2.

 

Contactless Reader Slot. 

Normally, each of these two reader slots is reported to the Microsoft Windows Smart Card Resource 

Manager. When the user requests that the Smart Card Resource Manager enumerate the list of 

available readers, both of these readers will be reported to the user. In the normal configuration, 

two readers are reported for each installed OMNIKEY 5121 Ethernet Encoder device. 
The Contact Reader is reported to the Smart Card Resource Manager using the same Encoder 

Device Name String that is displayed in the 

Select Encoder

 drop-down list. In the example below 

the Contact Reader will be reported using the name string 

OMNIKEY 5x21 LAN B1234567 0

 

The associated Contactless Reader is reported to the Smart Card Resource Manager using the same 

Encoder Device Name String, but with a 

-CL

 tag appended to the end of the Printer Serial Number. 

With recent versions of the Microsoft Windows operating system (both server and workstation) the 

number of simultaneously installed and supported smart card readers is limited to a maximum value 

of 10. Therefore, the Microsoft Windows Smart Card Resource Manager will support only 5 

OMNIKEY 5121 Ethernet Encoder devices installed using the normal configuration (i.e., with both 

reader slots enabled). 
The OMNIKEY 5121 Ethernet Encoder Utility supports the ability to disable either the Contact Reader 

Slot or the Contactless Reader Slot associated with all currently installed OMNIKEY 5121 Ethernet 

Encoder devices. This functionality is controlled by selecting one of the Encoder Slot Management 

options. 

Note:

 any changes made to the Encoder Slot Management group will not become effective until 

after all currently installed OMNIKEY 5121 Ethernet Encoder devices are manually restarted or the 

host system is rebooted. Any OMNIKEY 5121 Ethernet Encoder device added after changes have 

been made to the Encoder Slot Management group settings will be affected by those new settings. 
Once any changes have been made to the Encoder Slot Management options group either the 

server/workstation must be rebooted, or each currently installed OMNIKEY 5121 Ethernet Encoder 

device instance must be manually restarted using the Restart Selected Encoder option of the 

Encoder Menu. 

 

 

Summary of Contents for OMNIKEY 5121


























Reviews: