HIAB 320T Operating Manual / Spare Parts List Download Page 18

Page: 18 / 135

▲

Do not lower the outrigger legs on the edge of an embankment,

soft shoulder, slope etc. Lower the outrigger legs only on a flat

surface.

▲

Slide the outrigger extension beams on both sides of the vehicle out

completely. Then lower the outrigger legs for support.

▲

If outrigger extension beams are not slide out completely,

then the crane can tip over.

▲

WARNING

Place the outrigger legs with low force on the ground.

Only for cranes with 2 outrigger legs :

Do not raise the vehicle! If you raise the vehicle with the outrigger legs

this can damage the outrigger legs.

▲

DANGER

Never operate the outrigger legs if the crane has a load.

▲

DANGER

Unfold the crane according to the

directions in the operation and

maintenance for your crane.

▲

Never unfold the loader from the

position shown in fig. 5

Summary of Contents for 320T








































































































































Search results

Summary of Contents for 320T

Reviews:

Related manuals for 320T

Brands by name

Popular brands

HIAB 320T, Operating Manual / Spare Parts List

Search results

Summary of Contents for 320T

Reviews:

Related manuals for 320T

Brands by name

Popular brands