background image

Wiring and Configuration

Pre-Release 052917

    JUMPER PIN SETTINGS

AUXILIARY RELAY TIMER (SEE 

NOTES).

H3 

LED LIGHT INDICATORS

LED 1 - 

GREEN LIGHT, PUMP TIMER AND 

OPERATION MODE INDICATOR. 

LED 2 -

 BLUE LIGHT, PRESSURE SENSOR.

H1 EMERGENCY DISCONNECT:

 REMOVE PIN IF 

WIRED TO EMERGENCY DISCONNECT.

H2 TIMER: 

MODE:

 

AUTO -

 FAN SPEED MODULATES 

DEPENDING UPON STATIC PRESSURE.

MANUAL -

 FAN SPEED OPERATES AT TRIM 

POTS SET AIR FLOW.

H4 DELAY: 

Y/20 AND W/30 SECOND FAN DELAY.

Y AND W 30 SECOND POST PURGE.

ZONE BOARD SEVEN BUILT-IN TIMERS FOR 
SAFE & RELIABLE OPERATION

** DURING SET-UP MOMENTARILY PRESSING 
THE 

RESET

 BUTTON CLEARS THE BUILT-IN 

TIMERS. PRESSING THE 

RESET BUTTON

 FOR 7 

SECONDS WILL RESET THE CPU.

MOMENTARILY PRESSING THE 

RESET BUTTON

 CLEARS THE BUILT-IN TIMERS. 

THIS OCCURS AFTER ANY INITIAL POWER UP 
OR POWER FAILURE. PRESS THE 

RESET 

BUTTON FOR 1 SECOND TO OVERRIDE.

STARTUP DELAY TIMER -

 

 

THE PANEL WILL NOT 

ACTIVATE ANY COOLING OR HEATING 
OPERATION UNTIL THE STARTUP DELAY HAS 
EXPIRED.

* START-UP DELAY TIMER = 3 MINUTES-FIXED
* SHORT CYCLE TIMER     = 3 MINUTES-FIXED
* CHANGE OVER TIMER  = 4 MINUTES-FIXED
* OPPOSING CALL TIMER = 20 MINUTES-FIXED
* STAGING TIMER = OFF OR 7-42 MIN.-ADJ.
* SUPPLY AIR LIMIT TIMER = 3 MINUTES-FIXED
* PURGE DELAY TIMER  = 90 SECONDS-FIXED

ZONE CONTROLLER

PRE-WIRED TO 2 ZONES, 3 AND 4 IF APPLICABLE

M6 - 24VAC TO CLOSE DAMPER
M4 - 24VAC TO OPEN DAMPER
M2 - CONSTANT 24 VAC HOT
M1 - COMMON 24 VAC

NOTES:

1)

 USE THERMOSTAT FAN SWITCH TO DISABLE/ENABLE CONTINUOUS FAN.

2)

 ‘C’ TERMINAL ON THERMOSTAT (COMMON) IS NOT NEEDED FOR SOME 

THERMOSTATS CONSULT THERMOSTAT INSTRUCTIONS FOR DETAILS.

3)

 W1 AND W2 ACTIVATES AUXILIARY RELAY (A3) ON CALL AND CAN BE USED 

WITH A1 AND/OR A2 AS DRY CONTACTS, ARMED 24VAC FROM THE ‘R’ 
TERMINAL, OR ARMED 110v FROM THE ‘L’ TERMINAL.

4)

 AUXILIARY HEATING RELAY TIMER ACTIVATES CIRCUIT FOR 5 MINUTES 

EVERY 24 HOURS STARTING WHEN POWER IS APPLIED TO THE UNIT. 

5) LED 1: INDICATOR LIGHT FOR FAN SPEED OPERATION AND AUXILIARY 

RELAY OPERATION. 

SEE BELOW FOR LIGHT OPERATION SEQUENCE.

 

6)

 SEE INSTALLATION MANUAL FOR MORE DETAILED WIRING DIAGRAMS.

7)

8)

 FAILURE TO SET PROPER AIR FLOW AND/OR OPERATION OF THE SYSTEM 

MAY RESULT IN DAMAGE TO EQUIPMENT. 

9)

 FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE 

INSTALLATION COULD CAUSE PERSONAL INJURY AND/OR PROPERTY 
DAMAGE.

10)

 ENSURE THAT THE FILTER IS KEPT CLEAN AT ALL TIMES.

11)

 MOTOR HAS PERMANENT LUBE BEARINGS AND DOES  NOT REQUIRE 

OILING.

12)

 WARRANTY VOID IF FAN COIL UNIT IS USED DURING CONSTRUCTION. 

 FOR SINGLE STAGE COOLING OPERATION USE Y2, OTHERWISE THE FREEZE 

STAT WILL BE BYPASSED.

INCREASE AIR FLOW
(CLOCKWISE)

DECREASE AIR FLOW
(COUNTER CLOCKWISE)

FAN ADJUSTMENT TRIM POTS

ON: (ACTIVE) 

PUMP TIMER STATUS

ON: (INACTIVE)

OFF:

FAN OPERATION MODE

NO LIGHT

D

W

Y

G

2 SECONDS

2 SECONDS

2 SECONDS

LED 1: (GREEN LIGHT) 
PUMP TIMER/OPERATION MODE INDICATOR LIGHT SEQUENCE

LED 2: PRESSURE SENSING INDICATOR (BLUE LIGHT)
H3 JUMPER PIN: AUTO OR MANUAL MODE

AUTO MODE: LED 2 WILL SPORADICALLY FLICKER (ON/OFF)

 

TO SHOW THAT IT IS PROPERLY SENSING PRESSURE IN THE SYSTEM.

* NO LIGHT

 INDICATES TRIM POT IS ABOVE NORMAL OPERATING RANGE 

(COUNTER CLOCKWISE DECREASE).

* SOLID LIGHT

 INDICATES TRIM POT IS BELOW NORMAL OPERATING 

RANGE (CLOCKWISE, INCREASE).

MANUAL MODE: LED 2 WILL BE OFF

, ADJUST EACH OF THE AIR FLOWS TO 

DESIRED CFM/LPS OUTPUT. 

ADJUSTING TRIM POTS: ON POWER START UP, ALLOW 45 SECONDS FOR 

SYSTEM TO PRESSURIZE BEFORE MAKING ANY CHANGES. 

DO NOT ADJUST MORE THAN A ½ TURN AT A TIME, ALLOW 30 SECONDS 
BETWEEN ADJUSTMENTS FOR THE PSB TO REACH SET POINT.

REFER AND COMPLETE COMMISSIONING REPORT PRIOR TO NORMAL 

OPERATION. FOR FULL DETAILS, REPORT IS AVAILABLE IN THE INSTALLATION 
MANUAL OR ONLINE AT 

WWW.HI-VELOCITY.COM.

10

Summary of Contents for HE-Z











Reviews: