background image

Operating Instruction Manual: 

OM-JCS-01 

Serial Number: 

ALL 

 

 

 

1.0 Inspection upon Receipt 

Upon receipt of the product, visually inspect the item for any evidence of shipping damage. Please note: 
the warranty does not cover shipping damage. Notify the courier immediately if shipping damage is found 
and refrain from putting the product into service. The carrier is responsible for repair and replacement costs 
resulting from damage that occurred in transit. 

 

2.0 Safety Precautions 

2.1 Introduction

 

Read and follow all the instructions and safety warnings carefully before handling, installation or 
use  of  any  hydraulic  equipment.  Failure  to  do  so  could  lead  to  equipment  damage,  equipment 
failure, personal injury or even death. Hi-Force will not be held responsible for any damage to the 

equipment, injury or death resulting from the unsafe use of, lack of maintenance to, or incorrect operation 
of the product. If in doubt on the correct use of any Hi-Force equipment, contact your nearest Hi-Force office 
or distributor. Only qualified personnel should be allowed to operate hydraulic equipment. If an operator has 
not been trained on high-pressure hydraulic equipment and its safe usage, consult your local Hi-Force sales 
office who can offer training courses for operators. 

 
2.2 General Hydraulic System Safety Precautions 

Failure to observe and obey the following safety precautions could result 
in property damage, significant personal injury or death; 

 

   

   

 

  When operating any hydraulic equipment, all operators should ensure that all necessary personal 

protective  equipment  (PPE)  is  worn,  as  specified  by  their  employer.  Steel  toe-cap  safety  shoes, 
safety glasses/visor, and protective gloves should be worn at all times. All relevant risk assessments 
should be completed before the use of the equipment. 

  Keep hydraulic equipment away from open flames and direct heat.

 

  Immediately replace any worn or damaged parts using genuine Hi-Force parts only. 

 

Failure to observe and obey the following safety precautions could result 
in  property  damage,  equipment  damage  or  minor/moderate  personal 
injury; 

  Servicing of hydraulic equipment must only be undertaken by a qualified technician.

 

 

 

Summary of Contents for JCS Series













Reviews: