Hi-Flame HF-517U Installation And Operation Instruction Manual Download Page 2

 

Safety Notice 

If this solid fuel room heater is not properly installed, a house fire may result. For your 
safety and to reduce the risk of fire, follow the installation instructions. Contact local 
building officials, fire officials or the authority having jurisdiction about restrictions and 
installation inspection requirements in your area, including the need to obtain a permit. 
Kindly save these instructions for future reference. 

 

VERY IMPORTANT 

PLEASE  READ  THIS  ENTIRE  MANUAL  BEFORE  YOU  INSTALL  AND  USE  YOUR  NEW 
ROOM  HEATER.  FAILURE  TO  FOLLOW  INSTRUCTIONS  MAY  RESULT  IN  PROPERTY 
DAMAGE, BODILY INJURY, OR EVEN DEATH! FAILURE TO READ AND FOLLOW THESE 
INSTRUCTIONS  BEFORE  YOU  PROCEED  MAY  RESULT  IN  DAMAGE,  VOIDING  YOUR 
WARRANTY. 

DO NOT INSTALL IN A MOBILE HOME. 

DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE. 

DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA OR 
ENGINE OIL. 

HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. 
CONTACT MAY CAUSE SKIN BURNS. 

 

Please contact the Hi Flame® dealer in your area if you have any questions 

about your stove that are not covered in this manual. 

 

 

Proposition 65 Warning

: Fuels used in gas, wood-burning or oil fired appliances, and the 

products of combustion of such fuels, contain chemicals known to the State of California to 
cause cancer, birth defects and other reproductive harm. California Health & Safety Code Sec. 
25249.6 

 

 

Summary of Contents for HF-517U

























Reviews: