background image

HF-LPS170 Wi-Fi&BLE User Manual 

 

Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)

 

- 14 - 

 

Federal Communication Commission Interference Statement  

This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference in a residential installation. This equipment generates, uses and can 

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications.  However, there is no guarantee that interference 

will not occur in a particular installation.  If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one of the following measures:  

- Reorient or relocate the receiving antenna.  

- Increase the separation between the equipment and receiver.  

- Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.  

- Consult the dealer or an experienced radio/TV technician for help.  

MODULE HINT : 

 

1.The module is limited to OEM installation only. 

2.The module is limited to installation in mobile or fixed application.

 

FCC Caution:  

Any changes or modifications not expressly approved by the party responsible for compliance could 

void the user's authority to operate this equipment.  

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions:  

(1) This device may not cause harmful interference, and 

(2) This device must accept any interference received, including interference that may cause 

undesired operation.  

 

 

Summary of Contents for HF-LPS170

















Reviews: