background image

 

 

 

 
AB- V-MA-650 

1 February 2021 

JF/RR 

LD900 and INS Commissioning Guide 

Introduction 

This commissioning guide will provide the information required to install the VERIPOS LD900 unit with INS, by 
detailing how an LD900 should be configured and how an IMU should be mounted, interfaced and configured. 

Contents 

Introduction

 

Prerequisites

 

INS Authorisation

 

GNSS Heading Antenna Installation

 

Reference Frames

 

IMU Placement

 

IMU Interfacing

 

Alignment / Calibration

 

Rotational Offset Adjustment

 

Configuration

 

Operation

 

Troubleshooting

 

Appendix A 

– Equipment Required

 

Appendix B - IMU Performance

 

 

The VERIPOS INS system consists of an LD900 (LD900 or LD900M model) receiver, authorised for INS use 
and operating in PPP mode with active GNSS heading. The LD900 presently supports integration with two 
Novatel IMU models, the IMU-ISA-100C and IMU-µIMU-IC: 

 

 

 

Novatel IMU-ISA-100C  (left) and Novatel  IMU-µIMU-IC  (right) 

INS operations can be configured and monitored using the LD900 MMI, or an interfaced Quantum software 
system. This guide will provide details for both options. 
 

Summary of Contents for VERIPOS INS


























Reviews: