SHEET TITLE :
SHEET NO. :
NOTICE:
HexaCrafter ltd. reserves proprietary
rights to this drawing and data shown
thereon. Said drawings and/or data
are CONFIDENTIAL and are not to
be reproduced for any purpose
without the written consent of
HexaCrafter ltd.
ISSUE / DATE:
DRAWN BY:
01-17-2017
ARR
HexaCrafter ltd.
2750 Northampton Road
Cuyahoga Falls, Ohio 44223
(330) 929-0989
www.hexacrafter.com
QXS-8
AIRFRAME ASSEMBLY
MANUAL -
REIP ROUND ELECT.
ISOLATION SYSTEM
DETAIL: REIP SYSTEM
STEP 10 - REIP ROUND ELECTRONICS VIBRATION ISOLATION - DJI PRODUCTS
AREA FOR FLIGHT CONTROLLER
AHCS-3X6 ALUMINUM
HEX
CAP SCREW
MAGNETIC INTERFERENCE:
ONLY NON-MAGNETIC
FASTENERS (ALUMINUM OR
NYLON) SHOULD BE USED
AROUND THE GPS / COMPASS
UNIT. STEEL FASTENERS MAY
CAUSE MAGNETIC
INTERFERENCE WITH THIS
TYPE OF ELECTRONIC
EQUIPMENT.
GPS/ COMPASS PUCK -
FASTEM TO GMP-1 WITH
DOUBLE SIDED TAPE-
PROVIDED BY OTHERS
GMP GPS MOUNTING PLATE
REIP-1 ROUND
ELECTRONICS
ISOLATION PLATE 1
TOP CENTER PLATE
ASSEMBLY OF
AIRCRAFT
IMU / NAZA/ A3
NOTE:
CHECK THAT IMU/
FC WITH BUILT IN IMU IS
CENTERED IN HOLE OF
IMUP AFTER ASSEMBLED-
MINIMUM 1/8" AIR GAP
BETWEEN IMU AND REIP
PLATES IS RECOMMENDED
AHCS-3X8 STEEL
HEX CAP
SCREW
3MX30FFAL
HEX STANDOFF
IMPORTANT NOTE!!:
THE RUBBER ISOLATION CYLINDERS ARE VERY
SOFT AND DELICATE. THIS IS BY DESIGN TO
PROVIDE DESIGNED SHOCK/ VIBRATION
PROTECTION. USE EXTREME CARE WHEN
TIGHTENING AND LOOSENING THE NUTS AS THEY
ARE EASILY DAMAGED. DO NOT OVERTIGHTEN.
THE USE OF THREADLOCK IS NOT RECOMMENDED.
THE CAREFUL USE OF FORCEPS AT THE END OF
THE RUBBER CYLINDERS WHEN TIGHTENING AND
LOOSENING IS RECOMMENDED. A SMALL LINE OR
DROP OF THREADLOCK CAN BE APPLIED AFTER
THE NUT IS TIGHTENED IF CONCERNED ABOUT THE
NUT LOOSENING. USE AN EXACTO KNIFE TO
"BREAK" THE LINE OR DROP OF THREADLOCK
PRIOR TO LOOSENING THE NUT.
IMPORTANT NOTE!!:
THE RUBBER ISOLATION CYLINDER THREADS ARE
US AND STANDOFFS ARE METRIC. DO NOT
ATTEMPT TO SCREW ISOLATION DAMPNER INTO A
STANDOFF. USE PROVIDE 4-40 US THREAD NUTS.
TSS-3X16
THREADED STEEL STUD
THREADLOCK COMPOUND RECOMMENDED
AT
3MX23FFAL
HEX STANDOFF - LEAVE 10MM OF
THREADS EXPOSED- WAIT 20 MINUTES TO
ALLOW THREADLOCK TO SET BEFORE
ASSEMBLING THROUGH PLATE AND INTO THE
3MX15FFAL
HEX STANDOFF
REIP-2 ROUND ELECTRONICS
ISOLATION PLATE 2
3MX25FFAL
HEX STANDOFF FOR DJI PRODUCTS
DETAIL: REIP SYSTEM
STEP 9 - REIP ROUND ELECTRONICS VIBRATION ISOLATION
NOTE:
DIFFERENT LENGTH STANDOFFS
MAY BE USED TO PROVIDE NEEDED
CLEARANCE FOR ADDITIONAL
PLATE MOUNTED ELECTRONICS.
VERIFY DOME CLEARANCE WHEN
USING DIFFERENT STANDOFFS.
NOTE:
DIFFERENT LENGTH STANDOFFS
MAY BE USED TO PROVIDE NEEDED
CLEARANCE FOR ADDITIONAL
PLATE MOUNTED ELECTRONICS.
VERIFY DOME CLEARANCE WHEN
USING DIFFERENT STANDOFFS.
IMU TO MOUNT HERE
NOTE:
CHECK THAT IMU IS
CENTERED IN HOLE OF
LEIP AFTER ASSEMBLED-
MINIMUM 1/8" AIR GAP
BETWEEN IMU AND LEIP
PLATE IS RECOMMENDED
IMUP-2 IMU PLATE - TYPE 2
IMUP-2 IMU PLATE - TYPE 2
DJI IMU OR FLIGHT CONTROLLER
WITH BUILT IN IMU
OR
PIXHAWK TO MOUNT HERE
NOTE:
HOLES ARE
PROVIDED IN PLATE FOR
BOLT-UP OF PIXHAWK 2.1.
EARLIER PIXHAW MOUNT
WITH DOUBLE SIDED TAPE
