background image

10

TEST THE SYSTEM

IMPORTANT: 

The crane/machine functions will 

operate during this check. Be certain that there are no 
obstacles near the crane/machine.

1. Position yourself in front of the receiver so that 

the LED is visible.

2. Apply power to receiver. 

- The LED should start flashing yellow to indicate 
that it is operating properly.

3. Press and release any toggle switch on the 

transmitter.

- The LED on the transmitter should flash green. 
The duration of the flashing is determined by the 
"TX Shutdown" setting in the H-Link program. 
Refer to HH-MFSHL H-Link Programming 
Manual.

- The LED on the receiver should flash 
green/yellow alternately while the switch is 
activated. This indicates that the receiver is 
detecting a valid signal from the transmitter.

4. Activate any switch on the transmitter again, but 

this time push in the E-Stop button while the 
green LED is flashing. Any machine movement 
should stop.

- The LED on the transmitter should turn red and 
immediately turn off. This indicates that the 
E-Stop contact is open. (crane/machine motions 
will NOT operate)

- The LED on the receiver should flash yellow.

5. Activate the motion toggle switches. There should 

be NO movement of the crane/machine motions 
with the E-Stop pushbutton activated.

IMPORTANT:

 If any function of the radio remote 

control activates with the E-Stop engaged, the 
radio remote control must not be used until it is 
repaired by a certified technician.

6. Pull the E-Stop button out. 

7. Activate the motion toggle switches to test the 

crane/machine functions.

8. Confirm that the crane/machine moves 

appropriately. Refer to Operator Procedures in 
the HH-MFSHL H-Link Programming Manual if 
the minimum and maximum speed setting of the 
hydraulic functions need to be adjusted.

9. If transmitter and receiver function properly, the 

system is ready for use.

10. If the receiver or transmitter does not operate 

properly, or if the crane/machine does not react 
as directed, shut the entire system down and 
refer to the Troubleshooting Section of this 
manual. If necessary, contact Hetronic or an 
authorized service technician.

RECEIVER

LED / Address

Learn Button

E-STOP

LED

TRANSMITTER

PRELIMINAR

Y COPY

Summary of Contents for HH-L-MFSHL TS7P




















Reviews: