background image

TW-810T 

19 

■  Initial Defect 

The Warranty for initial defect is valid for 30 days from the date of shipment of the Product.    In case an initial defect 

is found, the defective product should be shipped to your dealer or our Sales Department within the period 

mentioned above.    Upon confirmation of the initial defect, the defect will be remedied free of charge either by repair 

or replacement with a new one. The shipping costs for the initial defect will be borne by the Company. However, this 

shall apply only within Japan.    The payer of overseas shipping costs including insurance fee, custom duty etc. for a 

customer who purchased the Product outside Japan shall be determined on mutual consultation. 

■  Disclaimer 

The Company will not be responsible for any direct or indirect damage and financial loss caused by malfunction or 

failure of the Product or its use. 

■  Period for Charged Repair 

After the Warranty Period expires, the Company will repair 

the Product for a fee on customer’s request during a 5 

year-period after termination of the Product on the condition that spare parts are available in stock at the Company. 

However, in case of unavoidable reasons such as elimination of parts, alternative parts or a substitution may be 

supplied. 

■  Other 

●  Regardless of the Warranty Period, repair shall only be performed in principle at the Company for purposes of 

using measurement equipment etc. for adjustment.    The shipping costs incurred at the time of shipment shall be 

borne by customer. Visiting repair service or a substitution during the Warranty Period are available on request 

for a fee.    Please contact your dealer or our Sales Department. 

●  If our Technical Department finds it difficult to reproduce failure of the Product received for repair, repair service 

or replacement may not be performed.    Also, technical investigation expenses for failure reproduction may be 

charged separately.     

●  Note that any information about the Product on our website, catalogues, manuals, technical materials and other 

materials is subject to change without notice.

 

 

Summary of Contents for TW-810T

























Reviews: