HERO S2650 User Manual Download Page 16 | Manualshive

Page: 16 / 23

background image

16

Instructions for use



Connect the electrical power supply cord, following the safety instructions

previously explained in this manual.



The machine does not have a general on/off switch, so when the power cord is

connected, the shaker is ready to operate.



When initially powered on, the shaker will perform a check cycle, in which the clamp

plate performs a repositioning operation.



Shown below are the control devices for operating the shaker:

Emergency Stop

Button

Control Panel

Can Loading

Tray

Front Door

Power Cord

Can Loading

Shelf

«
...
14
15
16
17
18
...
»

Summary of Contents for S2650
























Reviews:

No comments

Related manuals for S2650

Brand: Fast Pages: 112

Brand: Paasche Airbrush Pages: 4

Brand: DeVilbiss Pages: 8

AIRCOMBI Phoenix 6530

Brand: wiwa Pages: 50

Brand: SnowEx Pages: 16

Brand: Ferm Pages: 120

Brand: AMBIC Pages: 9

Brand: ZUPAN Pages: 34

Brand: Sagola Pages: 20

Brand: Sagola Pages: 64

Brand: Raider Pages: 72

Brand: VAUPEL Pages: 11

Brand: Harbor Freight Tools Pages: 12

Brand: Eastwood Pages: 9

Brand: Eastwood Pages: 8

Brand: Tritech Pages: 60

Brand: Eastwood Pages: 16

Brand: VAUPEL Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands