GB
- 16 -
This shuts down the socket (6). You can reactivate
the socket (6) by pressing the overload cut-out
(3).
Notice! If this happens, reduce the electric power
you are taking from the generator or remove any
defective connected appliances.
7. Cleaning, maintenance, storage
and ordering of spare parts
Switch o
ff
the motor and pull the spark plug boot
from the spark plug before doing any cleaning
and maintenance work on the equipment.
Notice! Switch o
ff
the machine immediately and
contact your service station:
•
In the event of unusual vibrations or noise
•
If the engine appears to be overloaded or
misfires
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could
attack the plastic parts of the equipment. En-
sure that no water can seep into the device.
7.2. Air
fi
lter (Fig. 5/6)
•
The air filter should be cleaned after every 30
hours of operation.
•
Remove the air filter cover (Fig. 5).
•
Remove the filter element (Fig. 6).
•
Clean the filter element with soapy water,
rinse with clear water and leave to dry well
before re-installing.
•
Assemble in reverse order
7.3. Spark plug (Fig. 7)
Check the spark plug for dirt and grime after 10
hours of operation and if necessary clean with a
copper wire brush. Thereafter service the spark
plug after every 50 hours of operation.
•
Pull off the spark plug boot with a twist.
•
Remove the spark plug with the supplied
spark plug wrench.
•
Assemble in reverse order
7.4 Maintenance
•
There are no parts inside the equipment
which require additional maintenance.
7.5 Storage
Notice! If you fail to follow these instructions
correctly, deposits may form on the interior of the
carburetor which may result in the engine being
more di
ffi
cult to start or the machine su
ff
ering per-
manent damage.
1. Carry out all the maintenance work.
2. Drain the fuel out of the tank (use a conventi-
onal plastic petrol pump from a DIY store for
this purpose).
3. When the fuel has been drained, start the en-
gine.
4. Allow the engine to run at idling speed until it
stops. This will clean the remainder of the fuel
out of the carburetor.
5. Leave the machine to cool (approx. 5 minu-
tes).
6. Remove the spark plug (see point 7.3).
7. Clean the exterior housing of the machine.
8. Store the machine in a cold, dry place where
it is out of the reach of ignition sources and
in
fl
ammable substances.
Restarting
1. Remove the spark plug.
2. Pull the starter cable several times to clean
the oil residue out of the combustion cham-
ber.
3. Clean the spark plug contacts or
fi
t a new
spark plug.
4. Fill the tank.
Transport
To transport the machine,
fi
rst empty the petrol
tank as described in section 2 in the section en-
titled “Storage”. Clean coarse dirt o
ff
the machine
with a brush or hand brush.
7.6 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Anl_HSE_720_SPK7.indb 16
Anl_HSE_720_SPK7.indb 16
27.09.2016 14:30:41
27.09.2016 14:30:41
