manualshive.com logo in svg

Hercules HD94B, Owner'S Manual & Safety Instructions, Page: 10 / 12

Share
Download
Hercules HD94B Owner'S Manual & Safety Instructions Download Page 10

Page 10

For technical questions, please call 1-888-866-5797.

Item 56564 

        

Troubleshooting

Problem

Possible Causes

Likely Solutions

Tool will 
not start.

1.  Battery Pack not properly 

connected. 
 

2.  Battery Pack not 

properly charged.

3.  Battery Pack worn out. 

4.  Internal damage or wear.  

(Carbon brushes or 
switch, for example.)

1.  Remove Battery Pack, make sure there are 

no obstructions, clean battery contacts on 
tool, reinsert the Battery Pack and press firmly 
until the Battery Pack locks in place.

2.  Make sure Charger is connected and operating properly.  

Give enough time for Battery Pack to recharge properly.

3.  Dispose of old Battery Pack properly or recycle.  

Replace Battery Pack.

4.  Have technician service tool.

Tool operates 
slowly.

1.  Forcing tool to work too fast.
2.  Battery Pack wearing out.

1.  Allow tool to work at its own rate.
2.  Dispose of old Battery Pack properly or recycle.  

Replace Battery Pack.

Performance 
decreases 
over time.

Carbon brushes worn or damaged. Have qualified technician replace brushes.

Excessive noise 
or rattling.

Internal damage or wear.  

Have technician service tool.

Overheating.

1.  Forcing tool to work too fast.
2.  Blocked motor housing vents.

1.  Allow tool to work at its own rate.
2.  Wear ANSI-approved safety goggles and 

NIOSH-approved dust mask/respirator while 
blowing dust out of motor using compressed air.

 

Follow all safety precautions whenever diagnosing or servicing the tool.   
Disconnect Battery Pack and Charger power supply before service.

Summary of Contents for HD94B













Reviews:

No comments