background image

MULTIPHONES GUEST POD II

HEADPHONE AMPLIFIER with TALENT CONTROL 

DESCRIPTION

The MultiPhones Guest Pod II is an individual headphone listening station for use with the MultiPhones Distributed 

Headphones System. It features a high performance headphone amplifier, plus two illuminated pushbuttons that 

are typically used by talent for “Cough” and “Talkback” functions. When used with the MultiPhones Master unit, 

power and audio are supplied by the Master. The Guest Pod can also be used as a “stand alone” headphone 

listening station (without a MultiPhones Master unit) if other powering is provided. The Guest Pod includes a Level 

control and both ¼” and 3.5mm headphone jacks.    

INSTALLATION 

The Guest Pod II is designed for tabletop, under-counter, or in-cabinet installation.  For tabletop use, install the 

rubber “feet” on the bottom of the enclosure.  Another option is to install two #8 screws in the tabletop, 3” apart, and 

slide the unit onto the screw heads. For under-counter installation, open the Guest Pod enclosure by removing the 

four corner screws from the bottom of the unit. Remove the top of the “clamshell” enclosure. Drill screw holes in the 

top as necessary and screw the top to the underside of the countertop.  Re-attach the lower section to the top with 

the bottom screws

.

The Guest Pod II can also be mounted into cabinetry using the optional Cabinet Mounting Plate. 

For use with MultiPhones Master unit:  

The Guest Pod(s) is connected to the MultiPhones Master unit using cat5 

cabling.  In most cases, unshielded cables can be used.  

WARNING!  DO NOT USE “CROSSOVER” CABLES.  

Connect up to 3 Guest Pods directly to the MultiPhones Master unit.  Each Guest Pod has 2 RJ45 connectors, 

which are wired in parallel. (Use either connector.)  Additional Guest Pods can be “daisy chained” together in any 

combination.  The total number of Guest Pods connected to one MultiPhones Master should not exceed 12 units. 

For use as a “stand alone” headphone listening station:

  For “stand alone” use, the Guest Pod requires a 

power source. Henry Engineering’s 

PowerPod 

or any 9-12 volt 

AC

 transformer may be used. The PowerPod will 

power up to 12 Guest Pods.  If a 12V AC transformer is used, each Guest Pod will require about 50 mA. 

Two ¼” TRS input jacks on the rear panel accept stereo balanced audio at about 0 dBu.  

Wire the inputs as follows:  

Tip = High; Ring = Low; Sleeve = Ground. 

Multiple Guest Pods can be used by “daisy chaining” them together with cat5 cabling.  Both power and audio will be 

distributed to all Guest Pods via the cat5 cables.  (To distribute power but not audio, remove R1, R19, R21, & R22 

from each Guest Pod unit in the system.) 

Talent control buttons: 

The two talent buttons (Cough and Talkback) must be wired to the Control RJ45 

connector by the user.  Any pin-out can be accommodated. Install wires between the switch terminals and the PC 

board pads labeled 

W1

 thru 

W8

, which correspond to the pins on the Control RJ45 connector.  Be sure to install a 

resistor in series with the LED in each switch according to the tally supply voltage being used. (12vdc = 2K ohms.) 

See the schematic on the reverse side for switch terminal details. 
OPERATION 

The Guest Pod II is simple in its operation.  The LEVEL controls adjust the audio level to the PHONES jacks.  Do 

not use both jacks at the same time.  Use headphones with an impedance between 24 and 600 ohms.  

Do not use older “8-ohm” headphones. Excessive listening levels can cause permanent hearing damage!

SPECIFICATIONS

INPUT   

 

From MultiPhones Master unit or 

 

 

 

¼” TRS jacks, 2X, 0 dBu, balanced 20K 

OUTPUT  

 

For 24 – 600 ohm headphones, ¼” and 3.5mm jacks 

FREQUENCY RESPONSE  5 Hz – 20 kHz, +/- 0.25 dB 

DISTORTION 

 

.005% typical 

NOISE   

 

-80 dBm typical 

POWER INPUT 

 

Supplied by MultiPhones Master unit, PowerPod, 

 

 

 

or 9-12 VAC transformer, 50mA per unit  

PHYSICAL DIMEN   

5.75”w X 1.75”h X 6.0”d, 1 LB 

MOUNTING PLATE

 (optional)

  5.5”w X 1.5”h, 6.0” behind panel; cutout: 4.5”w X 1.0”h  

Specifications subject to change without notice.   

 

 

 

Rev. 1/19 

HENRY ENGINEERING 

PO Box 3796 

Seal Beach, CA 90740 

Tel: 562.493.3589 

www.henryeng.com 

TM

Reviews: