manualshive.com logo in svg

Henny Penny OFE- 290, Operation

Share
Download
Henny Penny OFE- 290 Operation Download Page 16

                       Model OFE- 290

3-15.    SPECIAL PROGRAM MODE

        (Continued)

Factory Presets (F/C, Gas/Electric, Speaker Volume,
Speaker Frequency, Codes, Initialize System)

1.

Press and hold the FUNCTION button for two seconds until
“REG PROGRAM” shows in the display.  As soon as
“REG PROGRAM” shows in the display, press and release
the FUNCTION button 3 times until “FAC PRESET” shows
in the display.

2.

When “CODE” shows on the display, enter 2957.  “DEG”
and “MODE” flashes in the display.  Press any of the product
buttons to toggle from ºF to ºC, and vice versa.

3.

Press and release the FUNCTION button and “TYPE”
and “FRYR” flashes in the display.  Press any of the product
buttons to toggle from “GAS” to “ELEC”, or vice versa.

4.

Press and release the FUNCTION button twice, and
“SPKR” and “VOL” flashes in the display.  The volume can
be changed from 01 to 10, 10 being the loudest.

5.

Press and release the FUNCTION button 3 times, and
“SPKR” and “FREQ” will flash in the display.  The frequency
can be set from 100 to 2000.

6.

Press and release the FUNCTION button 10 times, and
“INITIALIZE SYSTEM” scrolls across the display.  Press
and hold any of the product buttons and the display will count
down from 5.  Once the display counts down, release the
product button, and the control will set factory preset param-
eters into the controls.

Before attempting to change the other modes in the Factory
Preset Mode, please call the Henny Penny Technical Service
Department at 1-800-417-8405, or 1-937-456-8405.

3-16

      703

Summary of Contents for OFE- 290



















Reviews:

No comments

Brands by name

Popular brands

Load more brands