background image

     

Model 

HHC-901/904

3-6.  OPERATING 

        CONTROLS -

        COUNTDOWN TIMERS

        (if applicable)

        (Continued)

Relay Type

7.    Press PROGRAM button and “relay type” shows in display.

8.  Press     buttons to choose “mech” (mechanical relay) or 

    “SSR” (solid state relay).  Set the HHC-901 & 904 controls to 

“SSR”.

Off-Set Calibration

9.    Press PROGRAM button and “offset calibrate” shows in 

   display.

10.  Press     buttons to calibrate the probe tempe 10  

    degrees.  The displayed temperature can be set to match the 

    actual interior temperature.

CPU Temperature

11.   Press PROGRAM button and “therm temp” shows in 

    display, along with the temperature of the PC board.

Outputs Test

12.  Press PROGRAM button and “outputs Test” shows in display.

13.  Press     buttons to turn on and off the heat outputs to help 

    in troubleshooting problems.

 Initialize  System

14.  Press PROGRAM button and “init system” shows in display

 15.  Press and hold either   button.

16.  The control beeps and the display counts down, “In-3”, 

    “In-2”, “In-1”.

17.  When display reaches “0”, release the button and the 

    initialization is complete and sets controls to default settings.

    If the   button is released before “0” is displayed, the 

    control will not initialize.

10.  Press the PROGRAM button to return to the Fahrenheit/Cel-

sius mode, or press and hold the PROGRAM button to exit 

programming.

3-8 

  Aug. 2009

Summary of Contents for HHC-901



























Reviews: