Henden H62SP Installation & Owner'S Manual Download Page 11

Henden 6 Star 2 Speed Pump Installation & Owners Manual

8. HENDEN

 REPAIR OR 

REPLACEMENT GUARANTEE

Our goods come with guarantees that cannot be 
excluded under the Australian Consumer Law. You are 
entitled to a replacement or refund for a major failure 
and compensation for any other reasonably foreseeable 
loss or damage. You are also entitled to have the goods 
repaired or replaced if the goods fail to be of acceptable 
quality and the failure does not amount to a major failure.
Should you experience any difficulties with your Henden 
product, we suggest in the first instance that you contact 
the installer of the product or your local Reece Irrigation 
& Pools branch. 
Alternatively you can phone Henden. On receipt of your 
claim, Henden will seek to resolve your difficulties, if the 
product is faulty or defective, advise you on how to have 
your Henden product repaired, obtain a replacement or  
a refund.
Henden does not cover normal wear or tear, or damage 
resulting from misuse or negligent handling, improper 
use for which the product was not designed or advertised, 
failure to properly follow the provided installation and 
operating instructions, failure to carry out maintenance, 
corrosive or abrasive water or other liquid, lightning or 
high voltage spikes, or unauthorized persons attempting 
repairs.  Where applicable, your Henden product must 
only be connected to the voltage shown on the nameplate.
Henden does not cover freight or any other costs incurred 
in making a claim. Please retain your receipt as proof 
of purchase; you MUST provide evidence of the date of 
original purchase when making a claim. 
Henden shall not be liable for any loss of profits or any 
consequential, indirect or special loss, damage or injury 
of any kind whatsoever arising directly or indirectly from 
Henden products. 
Should your Henden product require repair or service after 
the guarantee period; contact your nearest Reece Irrigation 
& Pools branch or phone the number below.
For a complete list of Reece Irrigation & Pools branches 
visit our website reece.com.au/storefinder or contact:

TECHNICAL AND AFTER SALES SUPPORT: 

1300 HENDEN (1300 436 336)

MAILING/MANUFACTURER ADDRESS: 

Davey Water Products 
6 Lakeview Drive, Scoresby,  
Victoria, 3179

 

HENDEN

 INSTALLATION & OWNERS MANUAL 

|

 

11

Henden Guarantee Period 

Four Years

Summary of Contents for H62SP













Reviews: