manualshive.com logo in svg

Hemisphere GPS Crescent A100, User Manual, Page: 2 / 44

Share
Download
Hemisphere GPS Crescent A100 User Manual Download Page 2

This device complies with Part 15 of the FCC rules. Operation is subject to the following 
two conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference received, including interference that may 

 

       cause undesired operation.

C

OPYRIGHT

 N

OTICE

Hemisphere GPS Inc. Precision GPS Applications

Copyright © Hemisphere GPS

 

(2007). All rights reserved.

No part of this manual may be reproduced, transmitted, transcribed, stored in a retrieval 
system or translated into any language or computer language, in any form or by any 
means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without 
the prior written permission of Hemisphere GPS Inc.

T

RADEMARKS

Hemisphere GPS and the Hemisphere GPS logo, Satloc and the Satloc logo, Mapstar, Air 
Star Outback Guidance and eDrive are trademarks of Hemisphere GPS. Other trademarks 
are the properties of their respective owners.

N

OTICE

 

TO

 C

USTOMERS

Contact your local dealer for technical assistance. To find the authorized dealer near you, 
call or write us at:

Hemisphere GPS

4110 9 Street S.E.                Telephone number: (403) 259-3311

 

Calgary, AB, Canada              Fax number:          (403) 259-8866

 

T2G 3C4                               E-mail address:      [email protected]

 

875-0163-000 (Crescent A100).book  Page 1  Tuesday, November 13, 2007  11:29 AM

Summary of Contents for Crescent A100













































Reviews:

No comments