EN-15
In STICK/MMA Welding (SMAW), for the connection
of the ground cable connector check for correct
polarity for the electrode you are going to use, refer
to the information on its box.
Most of the electrodes requires to connect the ground
cable on the negative (minus) connector -
C
- and to
connect the electrode holder on the positive (plus) -
B
-.
MMA MODE (UNITECH 328-358C - X4 WIRE
FEEDER)
Enable the MMA mode (
L11
LED) through the
T2
key.
D1
displays the welding current that is adjustable
through the
E1
knob.
HOT-START
•
In MMA mode (
L11
ON),
D2
displays the adju-
sted HOT-Start value.
•
Adjust the value through
E2
. (Value from 0 to
50). DEFAULT value 0.
ARC-FORCE
•
In MMA mode (
L11
ON), press
T3
to display
the ARC-FORCE value on
D2
.
•
Change the value through
E2
and confirm
with
T2
(Value from 0 to 20). DEFAULT value
0.
VRD
•
In MMA mode (
L11
ON), press
T3
to enable
or disable the VRD function.
•
Change the value through
E2
and confirm
with
T2
.
It is possible to enable or disable the VRD function
even from BASIC SETUP. See Basic SETUP section
MMA WELDING
on:
no-load volatged lowered to 12 V.
oFF:
not lowered no-load voltage. DEFAULT value
For the X4 wire feeder, the same values displayed
on
D1
and
D2
are also respectively displayed on
D3
and
D4
of Unitech 418 and 558 generators, but
setting is always possible only through
E1
and
E2
on the wire feeder.
MMA MODE (UNITECH 418-558 GENERA-
TORS)
With the wire feeder disconnected from the generator,
enable the MMA mode (
L20
ON) by holding
T5
for
3s..
D3
displays the welding current that is adjustable
through
E3
.
HOT-START
•
In MMA mode (
L20
ON), press
T5
to select
the HOT-START function (
L21
ON)
•
Adjust the value through
E3
.
D4
displays the
value. (Value from 0 to 50). DEFAULT value 0.
ARC-FORCE
•
In MMA mode (
L20
ON), press
T5
to select
the ARC-FORCE function (
L22
ON).
•
Adjust the value through
E3
.
D4
displays the
value. (Value from 0 to 20). DEFAULT value 0
(0÷20 def: 0)
VRD
By entering the BASIC SETUP menu it is possible to
adjust the VRD parameter. See Basic SETUP section.
on:
no-load voltage lowered to 12 V.
oFF:
not lowered no-load voltage. DEFAULT value
Connect the earth cable to the Positive output
terminal (plus) -
B
- on the front of the unit and the
earth clamp to the workpiece.
Connect the Tig torch to the negative output terminal
(minus) -
C
- on the front of the unit.
TIG MODE (UNITECH 328-358C -
X4 WIRE FEEDER)
Enable the MMA mode (
L12
LED) through the
T2
key.
D1
displays the welding current that is adjustable
through the
E1
knob.
RAPID SET UP MENU – TIG (VCut)
•
In TIG mode (
L12
ON) hold
T3
for 5s at least
to change the parameter VCut displayed on
D2
.
•
Change the value through
E2
and confirm
with
T2
.
It is possible to change the VCut value even from
BASIC SETUP. See Basic SETUP section
For the X4 wire feeder, the same values displayed on
D1
and
D2
are also respectively displayed on
D3
and
D4
of Unitech 418 and 558 generators, but
setting is always possible only through
E1
and
E2
on the wire feeder..
TIG WELDING
TIG MODE (UNITECH 418-558)
With the wire feeder disconnected from the generator,
enable the TIG mode (
L20
blinking) by holding
T5
for 3s..
D3
displays the welding current that is adju-
stable through
E3
.
TIG (VCut)
By entering the BASIC SETUP menu it is possible to
adjust the VCut parameter. See Basic SETUP section.
The
VCut
parameter varies the TIG lift arc extingui-
shing voltage to avoid defects on the welded piece.
Aut (Automatic):
the extinguishing voltage varies with the
set current (DEFAULT value)
15 V - 40 V:
a fixed arc extinguishing length can be set
oFF:
extinguishing voltage is the same as the no-load
voltage of the generator
Summary of Contents for UNITECH 328
