Helmholz 700-862-WAL01 Quick Start Manual Download Page 22

 

Quickstart Guide WALL IE /WALL IE PLUS | Version 15 | 25.08.2022 

22 

Order no. 

700-862-WAL01 

Name 

WALL IE PLUS, Industrial NAT Gateway/Firewall 

Dimensions (D x W x H) 

34.5 x 101.5 x 75.5 mm 

Weight 

approx. 230 g 

WAN/LAN interface 

 

 

Number 

8, switched 

 

Type 

100Base-Tx/1000Base-T 

 

Connection 

RJ45 socket 

 

Transmission rate 

100/1000 Mbps 

Operating modes 

Bridge, NAT (Basic NAT, NAPT) 

Packet filter 

IPV4 addresses, protocol (TCP/UDP), ports (“WAN to LAN” and “LAN to WAN” 
separate), MAC addresses (black & whitelisting) 

Status indicator 

4 LEDs function status, 8 LEDs Ethernet status 

Voltage supply 

24 V DC, 18–30 V DC 

Current draw 

max. 275 mA at 24 V DC 

Power dissipation 

max. 6,7 W 

Ambient conditions 

 

 

Installation position 

Any 

 

Ambient temperature 

0 °C ... +60°C 

 

Transport and storage temperature 

-40 °C ... +85°C 

 

Relative air humidity 

95 % r H without condensation 

 

Pollution degree 

 

Protection rating 

IP20 

Certification 

CE 

RoHS 

Yes 

REACH 

Yes 

 

The contents of this Quick Start Guide have been checked by us so as to ensure that they match the 
hardware and software described. However, we assume no liability for any existing differences, as 
these cannot be fully ruled out. The information in this Quick Start Guide is, however, updated on a 
regular basis. When using your purchased products, please make sure to use the latest version of this 

Quick Start Guide, which can be viewed and downloaded on the Internet from 

www.helmholz.de

. 

Our products contain open source software, among others. This software is subject to the respectively relevant 
license conditions. We can send you the corresponding license conditions, including a copy of the complete license 
text together with the product. They are also provided in our download area of the respective products under 

www.helmholz.de

. We also offer to send you or any third party the complete corresponding source text of the 

respective open source software for an at-cost fee of 10.00 Euro as a DVD upon request. This offer is valid for a 
period of three years, starting from the date of product delivery. 

Our customers are important to us, we are happy to receive suggestions and ideas for improvement. If you have any 
questions regarding the use of the product, please contact Helmholz Support by phone or send an e-mail to 

[email protected]

. 

All trademarks shown or mentioned in this document are the property of their respective owners or manufacturers. 
The representation and naming serve exclusively to explain the use and setting options of the products documented 
here. 

Summary of Contents for 700-862-WAL01























Reviews: