HELLER HCVH2000 User Manual Download Page 3

 

Do not operate the product with a damaged plug or cord. Return the complete product to the 

place of purchase for inspection, refund or replacement. 

 

If the supply cord is damaged, the cord must be replaced by the manufacturer, its service agent 

or similarly qualified persons in order to avoid hazard.   

 

Do not immerse or expose the product or flexible cord to rain, moisture or any other liquid. 

 

Switch off and unplug from outlet when the product is not in use and before cleaning the unit. 

 

To avoid personal injuries or property damage, do not insert any body parts (e.g. finder) or 

objects through the air inlet or outlet openings when the heater is operating. 

 

This product is intended for normal domestic/household use only and should not be used for 

industrial purposes. 

 

From time to time, please check the cord for damage. Never use the appliance if the cord or any 

part of the appliance shows signs of damage. 

 

Repairs to electrical appliances should only be performed by a qualified electrician. Improper 

repairs may place the user at serious risk. 

 

Do not run the main cable under carpets, rugs, etc. 

 

Do not allow the mains cable to hang over sharp edges or come into contact with hot surfaces. 

 

Never immerse the product in water or any other liquids. 

 

Before cleaning the appliance, ensure it is unplugged from the power and that it is completely 

cooled. 

 

Do not clean the appliance with abrasive chemicals. 

 

Always disconnect the heater when moving it from one location to another. 

 

The use of attachments or accessories not recommended or sold by the product distributor may 

cause personal or property hazards or injuries. 

 

Do not use the heater in reach of a shower, bath or a swimming pool. 

 

Heater is not located immediately below a socket-outlet. 

 

The surfaces of the heater are very hot during operation. Avoid contact with the wind outlet. Use 

handles and knobs if necessary. 

 

Do not twist or wrap the power cord around the appliance as this may cause the insulation to 

weaken and split, particularly where it enters the unit. Fully unwind the cord before use as a 

coiled cord may overheat. 

 

Use of an extension cord is not recommended. However, if it is absolutely necessary ensure the 

cord is short as possible (long cords coiled up can overheat and cause tripping accidents). 

 

Do not use the appliance on the same socket or electric circuit with other electrical appliances so 

as to prevent the circuit from being overloaded, which will cause fire. Please do not prolong the 

power cords by yourself or use movable socket. 

 

Ensure the cord is fully extended before use and accommodate it so that it is not in touch with 

any part of the heater. 

 

Do not use the heater in areas such as garages where petrol or other flammable substances are 

used or stored. Do not use the heater when flammable sprays, liquids, solvents and glues or 

flammable fumes may be present. 

 

Keep combustible materials such as furniture, pillows, bedding, clothes and curtains at least 1m 

away from the appliance. 

Summary of Contents for HCVH2000










Reviews: