Heliocentris Energy Manager 1.3 Instruction Manual Download Page 19

Page: 19 / 78

Getting Started

Energy Manager 1.3 - Instruction Manual

Getting Started

4.1

Scope of Delivery

The following components are delivered by Heliocentris:



Energy Manager



Wiring board



Grounding cable (2 m)



Connecting cable (2 m) from Energy Manager

to –48 VDC distribution



Set of connectors



Sensors (optional)

TIP

On customer request Heliocentris takes responsibility for the delivery and
installation of all hardware and software components for power generation in
the telecommunication site.

4.2

Unpacking and Installation

To install the Energy Manager the following steps are necessary:



Unpacking and Visual InspectionInstallation in a 19-inch rack



Connecting sensor cables to wiring board



Grounding



Connecting the power supply



Inserting SIM card

TIP

A connection to an external power supply grid is realized exclusively by

the customer or a qualified company.

4.2.1

Unpacking and Visual Inspection

A delivery receipt is delivered with the device.



Check for the correct number as per delivery receipt.



Check all parts for external damage.

Summary of Contents for Energy Manager 1.3















































































Search results

Summary of Contents for Energy Manager 1.3

Reviews:

Related manuals for Energy Manager 1.3

Brands by name

Popular brands

Heliocentris Energy Manager 1.3, Instruction Manual

Search results

Summary of Contents for Energy Manager 1.3

Reviews:

Related manuals for Energy Manager 1.3

Brands by name

Popular brands