background image

Cattle clipper Xperience 

33

7 Troubleshooting

7.1 Safety information

 DANGER

Mortal danger from electrical current!

Mortal danger can result from contact with current-carrying conductors or components!

 

Pull the plug from the socket before you start troubleshooting.

 

Repairs to electrical devices must only be carried out by the factory service 

department or specialists who have been trained by the manufacturer.

7.2 Causes of malfunctions and their rectification

Malfunction

Possible cause

Corrective measure

Upper blades moving 

too little.

Leaf springs have broken.

Notify customer service.

Square end of eccentric 

shaft or eccentric shaft worn 

(insufficient lubrication).

Upper blade does not 

move.

Defective gear.

Notify customer service.

Adjusting knob is 

jammed.

Thread is dirty or rusty.

Notify customer service.

Pressure spring is jammed.

Leaf springs in the 

head mount are too 

loose.

Comb plate screws are loose. Tighten the comb plate screws.

Play between 

swivelling lever and 

leaf spring.

Leaf springs and/or cylinder 

head screws are worn.

Notify customer service.

Swivelling lever is 

difficult to move up 

and down.

Centring sleeve lost.

Notify customer service.

Motor not running.

Burnt smell emanating from 

the motor housing; motor 

burnt.

Notify customer service.

Motor and/or electronics 

defective.

Notify customer service.

Motor runs very slowly. Clipping blades not lubricated 

adequately.

Lubricate the clipping blades.

Motor and/or electronics 

defective.

Notify customer service.

Summary of Contents for Xperience/D






















Reviews: