HEIDENHAIN TNC 426 User Manual Download Page 136 | Manualshive

Page: 136 / 502

background image

5 Programming: Tools

5.3 T

ool Compensation

5.3 Tool Compensation

Introduction

The TNC adjusts the spindle path in the tool axis by the compensation
value for the tool length. In the working plane, it compensates the tool
radius.

If you are writing the part program directly on the TNC, the tool radius
compensation is effective only in the working plane. The TNC
accounts for the compensation value in up to five axes including the
rotary axes.

Tool length compensation

Length compensation becomes effective automatically as soon as a
tool is called and the tool axis moves. To cancel length compensation
call a tool with the length L=0.

For tool length compensation, the TNC takes the delta values from
both the

TOOL CALL

block and the tool table into account:

Compensation value =

L

+

DL

TOOL CALL

+

DL

TAB

where

If a part program generated by a CAD system contains
surface-normal vectors, the TNC can perform three-
dimensional tool compensation, see “Three-Dimensional
Tool Compensation,” page 114.

If you cancel a positive length compensation with

TOOL

CALL 0

, the distance between tool and workpiece will be

reduced.

After

TOOL CALL

, the path of the tool in the tool axis, as

entered in the part program, is adjusted by the difference
between the length of the previous tool and that of the
new one.

L

is the tool length

L

from the

TOOL DEF

block or tool

table.

DL

TOOL CALL

:

is the oversize for length

DL

in the

TOOL CALL

block

(not taken into account by the position display).

DL

TAB

is the oversize for length

DL

in the tool table

«
...
134
135
136
137
138
...
»

Summary of Contents for TNC 426























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TNC 426

Brand: Quickmill Pages: 3

Brand: Valor Pages: 20

Brand: IFM Pages: 32

Brand: IFM Pages: 25

Brand: IFM Pages: 21

ioControl CR2050

Brand: IFM Pages: 126

ecomat 100 R 360

Brand: IFM Electronic Pages: 16

Ecomot300 AC2630

Brand: IFM Electronic Pages: 11

Brand: IFM Electronic Pages: 23

Brand: Maestra Pages: 22

Brand: Tamas Pages: 12

Brand: Tait Pages: 3

Brand: Watlow Pages: 4

Brand: K&G GROEP Pages: 27

Brand: CAME Pages: 2

Brand: CalAmp Pages: 13

Brand: Daruifuno Pages: 24

Brand: Hunter Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands