background image

 

 

Please make sure that the earthing is not interrupted or destroyed when carrying out 
cleaning and maintenance work! 

 

 

3. Delivery & handling of the modules 

The goods must be checked immediately upon delivery to ensure completeness and integrity. Only damages which are 
noted  on  the  driver’s  delivery  receipt  and  are  immediately  communicated  in  written  form  to  Heckert  Solar  can  be 
recognised as transport damages.  

In general, our brand modules are packed upright on a one-way pallet of up to 30 or max. 19 modules. Take care when 
unpacking, transporting and storing the modules. We recommend keeping the modules in their packaging until ready 
for installation. Always set the pallets on a reinforced level ground and do not stack them under any circumstances. 

 

Standard   
packaging

 

Picking 
packaging

 

 

Number of modules/ 
pallets

 

20-30 

1-19 

 

External dimensions 
(W x L x H)

 

1.2 m x 1.16 m x 1.94 m 

1.2 m x 1.16 m x 1.94 m 

 

Weight of full pallet 

 

660 kg 

430 kg 

 

Quantity per truck 

 

22 pallets * 30 modules = 660 pcs. 
 

22 pallets * 19 modules = 18 pcs. 
 

 

 

 

The packaging is not film-wrapped and is therefore not resistant to rain! 

 

Please be sure to observe the unpacking instructions on the packaging! Never remove 
the rear retaining strap from pallets with 30 modules! 

 

 

Summary of Contents for NeMo 4.1 80 M




















Reviews: