HEC HEC9AFM Service Manual Download Page 6

                                        Version:00.00

                   

Edition: 2008.04 

               

Dishwasher

                 

     

  Model: HEC9AFM/HEC9AFMS

 

 

 

5

Connect the cold water supply hose to a threaded 3/4(gas) connector and make sure that it 
is fastened tightly in place (see Fig 1).If the water pipes are new or have not been used for 
an extended period of time,let the water run to make sure that the water is clear and free of 
impurities.If this precaution is not taken,there is a risk that the water inlet can get blocked 
and damage the appliance. 

5.4 Hot Water Connection

 

The water supply to the appliance can also be 
connected to the house's hot water line (centralised 
system, heating system), as long as it does not exceed a 
temperature of 60

   

In this case, the wash cycle time will be shortened by 
about 15 minutes and the wash efficiency slightly 
reduced. 
The connection must be made to the hot water line 
following the same procedures as those for the 
connection to the cold water line. 

Attention: 

The special plastic hose support must be solidly 
fastened to the wall to prevent the drain hose from 
moving and allowing water to spill outside the drain. 

Electrical Connection   

After making sure that the voltage and frequency values 

for the current in the home correspond to those on the rating plate (located on the stainless 
steel inner door of the appliance) and that the electrical system is sized for the maximum 
voltage on the rating plate, insert the plug into an electrical socket which is earthed properly 
(the earthing of the appliance is a safety requirement mandated by law). If the electrical 
socket to which the appliance must be connected is not appropriate for the plug, replace the 
plug, rather than using adaptors or the like as they could cause overheating and burns.

 

5.5 Drain Hose Connection 

Insert the drain hose into a drain pipe with a minimum diameter of 4cm,or let it run into the 
sink, making sure to avoid bending or crimping it. Use the special plastic support that comes 
with the appliance (see Fig.2). The free end of the hose must be at a height between 40 and 
100 cm and must not be immersed in water. 

Summary of Contents for HEC9AFM




















Reviews: