Heatrae Sadia SUPREME 150SS Fitting Instructions And User Manual Download Page 13

13

10.0 SPARE PARTS

The following comprehensive list of spare parts is available for your
Supreme water heater.  Please refer to the rating label on the right
hand side of your heater before ordering to ensure the correct spare
parts are obtained.

DO NOT REPLACE WITH PARTS NOT RECOMMENDED BY
HEATRAE SADIA - THIS WILL INVALIDATE YOUR GUARANTEE
AND MAY RENDER THE INSTALLATION DANGEROUS.

1.

Element assembly

(incorporating start dry cutout)

95 606 952

2.

Element assembly sealing gasket

95 611 816

3.

Primary cutout (vent pipe)

95 612 001

4.

Solenoid valve assembly

95 605 877

5.

Level sensor assembly (150 model)

95 612 010

6.

Level sensor assembly (165 & 180 models) 95 612 011

7.

Circuit board (150,165,180 models)

95 615 007

8.

Wiring harness (4way inc. diodes)

95 612 006

9.

Wiring harness (complete)

95 612 013

10.

Thermistor control/steam

95 612 696

11.

Outlet tap headwork (inc. handle)

95 605 019

12.

Outlet tap stem

95 605 832

13.

Outlet tap cup seal

95 611 731

14.

Bezel for tap & cover

95 605 020

15.

Stainless cover assy. & screws (150 model) 95 614 003

16.

Stainless cover assy. & screws (165 model) 95 614 004

17.

Stainless cover assy. & screws (180 model) 95 614 005

18.

Steam condenser assembly (150 model)

95 607 015

19.

Steam condenser assembly (165 model)

95 607 016

20.

Steam condenser assembly (180 model)

95 607 018

21.

Condenser sealing gasket (150 model)

95 611 817

22.

Condenser sealing gasket (165 model)

95 611 819

23.

Condenser sealing gasket (180 model)

95 611 820

24.

‘O’ ring kit

95 611 002

25.

Hose kit (low pressure)

95 607 014

26.

Hose kit (high pressure)

95 607 013

27.

Outlet spout plastic - tank

95 604 668

Summary of Contents for SUPREME 150SS





















Reviews: