Heatrae Sadia Hotflo 10 Fitting Instructions And User Manual Download Page 15

15

10.0 GUARANTEE

This product is guaranteed against faulty materials and manufacture for a     

period of 2 years from the date of purchase provided that:

1.  

The  unit  has  been  installed  in  accordance  with  the  Installation  and 

User Instructions  and all relevant Codes of Practice and Regulations 

in force at the time of installation, and  that all necessary controls and 

safety valves have been fitted correctly.

2.

  

Any valves and controls are of the Heatrae Sadia recommended type 

and specification.

3.

  

The unit has not been modified or tampered with in any way and has 

been  regularly  maintained  as  detailed  in  the  Installation  and  User 

Instructions.

4.

  

The unit has been used only for heating potable water.

The unit is not guaranteed against damage by frost and the inner container 

with  integral  immersion  heater  is  not  guaranteed  against  excessive  scale 

build-up.

This Guarantee in no way affects the statutory rights of the consumer.

The policy of Heatrae Sadia is one of continuous product development and, 

as such, we reserve the right to change specifications without notice.

11.0 ENVIRONMENTAL INFORMATION

Heatrae Sadia products are manufactured from many recyclable materials.

At the end of their useful life they should be disposed of at a Local Authority 

Recycling Centre in order to realise the full environmental benefits. Insulation 

is by means of  CFC-free polyurethane foam.

This water heater does not contain substances harmful to health; it does not 

contain any asbestos.

Summary of Contents for Hotflo 10

















Reviews: