Heatrae Sadia ELECTROMAX SOLAR Installation & Servicing Instructions Manual Download Page 46

Page: 46 / 80

4.8.6 PROGRAMMING MENU

The programming menu is used to the check parameters which may be changed.

To check / alter a parameter:

Select the programming sub menu as shown in section 4.8.4

•

Press UP or DOWN to scroll to the required parameter.

•

Press RIGHT to select the parameter. The icon will flash.

•

Press UP to increase the parameter value.

•

Press DOWN to decrease the parameter value.

•

Press RIGHT and the OK icon will flash.

•

Press RIGHT to confirm the parameter setting.

•

4.8.7 MANUAL OPERATION MENU

The manual operation menu allows the solar sytem to be operated by hand for test / service

purposes.

NOTE: During manual operation there is no auotmatic regulation of the system.

To manually operate the solar pump:

Select the manual operation sub menu as shown in section 4.8.4

•

Press UP or DOWN to switch the pump ON or OFF.

•

Press RIGHT to confirm the setting.

•

NOTE: Automatic regulation will be re actived after 8 hours.

FIGURE 31: PROGRAMMING MENU ICONS

DESCRIPTION

FACTORY SET

65°C

100%

RANGE

15 - 95°C

3 - 40 K

2 - 25 K

30 - 100%

INDICATION

01°C max.

dT max 7 K

dT min 3 K

min 100

MAXIMUM STORAGE TANK

TEMPERATURE

STORAGE TANK SWITCH ON

DIFFERENCE (dTon)

STORAGE TANK SWITCH OFF

DIFFERENCE (dToff)

PUMP SPEED CONTROL

(100% = SPEED CONTORL OFF )

FIGURE 32: MANUAL OPERATION MENU ICONS

DESCRIPTION

RANGE

1 = ON

0 = OFF

INDICATION

SWITCH SOLAR CIRCULATION PUMP ON / OFF

Summary of Contents for ELECTROMAX SOLAR

















































































Search results

Summary of Contents for ELECTROMAX SOLAR

Reviews:

Brands by name

Popular brands

Heatrae Sadia ELECTROMAX SOLAR, Installation & Servicing Instructions Manual

Search results

Summary of Contents for ELECTROMAX SOLAR

Reviews:

Brands by name

Popular brands