Heatrae Sadia ELECTROMAX SOLAR Installation & Servicing Instructions Manual Download Page 26

Page: 26 / 80

3.6.5 CONNECTION TO THE DIVERTOR VALVE AND EAST WEST COLLECTORS

A divertor valve (supplied loose) is included with East/West Electromax Solar models.

The Electromax Solar, divertor valve and the solar collectors are connected as follows:

The Electromax Solar return is connected to the divertor valve connection marked AB.

•

Divertor valve connection marked A is connected to the East collector return.

•

Divertor valve connection marked B is connected to the West collector return.

•

The Electromax Solar flow is connected to both the East and West collector flows.

•

Connection to the divertor valve is made be 22mm compression fittings. 22mm copper tube

or stainless steel flexible tube may be used. Adaptors to connect 22mm compression fittings

to stainless steel flexible tube are available (accessory code 5122238).

The solar expansion vessel should be connected to the Electromax solar return before the

divertor valve.

The divertor valve should be sited as close to the Electromax Solar as possible.

FIGURE 14: DIVERTOR VALVE

ELECTROMAX

SOLAR

FLOW

SOLAR

RETURN

SOLAR

EXPANSION

VESSEL

DIVERTOR

VALVE

EAST

COLLECTOR

WEST

COLLECTOR

Summary of Contents for ELECTROMAX SOLAR

















































































Search results

Summary of Contents for ELECTROMAX SOLAR

Reviews:

Brands by name

Popular brands

Heatrae Sadia ELECTROMAX SOLAR, Installation & Servicing Instructions Manual

Search results

Summary of Contents for ELECTROMAX SOLAR

Reviews:

Brands by name

Popular brands