Heatilator ST42A Owner'S Manual Download Page 17

Page: 17 / 52

Heatilator • ST42A US-CAN • 4012-039 Rev D • 11/07

A. Chimney Requirements

Vertical distances are measured from the base of the

re-

place as shown in Figure 5.2.

To determine the chimney components needed to complete
your particular installation, follow the steps below:

• Determine the total vertical height of the fireplace

installation. This dimension is measured from the base of
the

replace assembly to the point where the smoke exits

the termination cap.

• Subtract the effective height of the

replace assembly from

the overall height of the

replace installation (measured

from the base of the fireplace to the bottom of the
termination cap).

• Refer to Table 5.1 to determine what components must

be selected to complete the

replace installation.

• Determine the number of ceiling

restops, stabilizers,

roof flashing, etc. required to complete the fireplace
installation.

d & g

Ceiling Firestop

58-7/8 in.

(1495 mm)

Effective

Height

a,b,c,f

11-10 in. (279-254 mm)

adapter required in

Canada.

Figure 5.2 Chimney Requirements (refer to list in Sect. 5.A.)

Table 5.1

• Do NOT connect this fireplace to a chimney flue

servicing another appliance.

• Do NOT connect to any air distribution duct or

system.

CAUTION

Fire Risk

• Must maintain 2 in. (51 mm) air clearance

to insulation and other combustible
materials.

WARNING

meters

a. Minimum overall straight height

14.0

4.27

b. Minimum height with offset/return

16.5

5.03

c. Maximum height

90.0

27.43

d. Maximum chimney length between an offset and

return

20.0

6.1

e. Maximum distance between chimney stabilizers

35.0

10.67

f. Double offset/return minimum height

22.0

6.71

g. Maximum unsupported chimney length between the

offset and return

6.0

1.83

h. Maximum unsupported chimney height above the

replace

35.0

10.67

i. Maximum unsupported chimney above roof

6.0

1.83

Note:

A maximum of two pairs offsets and returns may

be used.

HEIGHT OF CHIMNEY
COMPONENTS

in.

Canada

Chimney Stabilizer

SL11

SL4

4-3/4

121

Ceiling Firestops

FS538

FS540

Offsets/Returns

SL1130

SL430

14-1/2

368

Roof Flashing

RF570

RF571

Chimney Sections*

SL1106

SL406

4-3/4

121

SL1112

SL412

10-3/4

273

SL1118

SL418

16-3/4

425

SL1136

SL436

34-3/4

883

SL1148

SL448

46-3/4

1187

n/a

SLA10

16-3/4

425

* Dimensions re

ect effective height.

Summary of Contents for ST42A





















































Search results

Summary of Contents for ST42A

Reviews:

Brands by name

Popular brands

Heatilator ST42A, Owner'S Manual

Search results

Summary of Contents for ST42A

Reviews:

Brands by name

Popular brands