Heatilator NB3630 Owner'S Manual Download

Page: 25 / 64

Heatilator • Novus BV • 4031-551 Rev B • 12/06

A. Remove the Shipping Materials

Remove shipping materials from inside or underneath the

rebox.

Shock Risk
Fire Risk

Use ONLY optional accessories approved
for this appliance.
• Using non-listed accessories voids

warranty.

• Using non-listed accessories may result

in a safety hazard.

• Only Hearth & Home Technologies

approved accessories may be used
safely.

WARNING

D. Install the Refractory

Install as directed in instructions included with refractory.

Explosion Risk

• Follow rockwool placement instructions

in this manual.

• Do NOT place rockwool directly over

burner ports.

• Replace rockwool material annually.
Improperly placed rockwool interferes with
proper burner operation.

WARNING

Lava Rock &
Vermiculite

Rockwool

Figure 12.1 Placement of Rockwool, Lava Rock and Vermiculite

Appliance Setup

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated in-
side the

rebox or underneath in the control cavity.

C. Accessories

Install approved accessories per instructions included with
accessories. Refer to Section 16.

To open the glass, see Section 12.G.

F. Firescreen

Removing Firescreen

• Open lower access panel and pull base of screen towards

you.

• The top of the screen will slide out of the screen retainers

at the top of the

rebox opening.

Replacing Firescreen

• Remove top grille assembly by lifting upwards and pulling

towards you.

• Slide top of screen panel into top screen brackets and

rotate bottom of screen to lower door latches.

• Close lower access panel and reinstall top grille.

E. Lava Rock, Vermiculite, Rockwool Placement

See Figure 12.1 for placement location.

Placing the Rockwool

Rockwool is shipped with this gas appliance. To place the
rockwool:

• Place a small amount of 1/2 in. diameter pieces (dime-size)

of rockwool on the burner pan so that the rockwool touches
but does not cover the holes in the burner pan. This will
provide the “glowing embers” look. It is not necessary to
use the entire bag. Save the remaining rockwool for future
use.

Placing the Lava Rock

• See Figure 12.1

Placing the Vermiculite

• Sprinkle on top of lava rock.

Summary of Contents for NB3630

































































Search results

Summary of Contents for NB3630

Reviews:

Related manuals for NB3630

Brands by name

Popular brands

Heatilator NB3630, Owner'S Manual

Search results

Summary of Contents for NB3630

Reviews:

Related manuals for NB3630

Brands by name

Popular brands