Heatilator HEIR36H-IFT Installation Manual Download Page 50

Page: 50 / 66

Heatilator • HEIR36-IFT, HEIR42-IFT, HEIR50-IFT Installation Manual • 2458-980 Rev. B • 8/17

D. Decorative Front Dimensions for Finish-

ing

A decorative front is required for this appliance. Only dec

orative fronts certified for use with this appliance model

may be used. Contact your dealer for a list of decorative

fronts that may be used. Once you have determined what

kind of decorative front and finishing material is going to

be used on the fireplace, you may use the table below

which shows the decorative front models and the finish

ing material thickness allowed. For an inside fit there is an

available template to ensure that proper decorative front

clearances are maintained with finishing material with

thickness greater than 1 inch.

COMBUSTIBLE MATERIAL

C (ARCH)

Figure 10.15 Inside Fit Decorative Fronts

The decorative fronts approved for use with this appli-

ance have been designed to be installed by two methods:

Overlap Fit

Inside Fit. Before beginning the installation,

it is important to determine which method will be used.

Overlap Fit Method:

These decorative fronts have been

designed to be installed over finishing material up to one

inch thick.

Inside Fit Method:

These decorative fronts may be re-

cessed into non-combustible finishing material up to 6

inches thick.

NOTICE:

Proper clearances from the fireplace opening

to any finishing material thicker than 1 inch MUST be

maintained.

NOTE:

Finishing templates are included with this product.

See Section 10.B.

Table 10.1. Approved Decorative Fronts

DIMENSIONS

3/4 IN.

1-1/4 IN.

FIRESCREEN DECORATIVE FRONTS

RECTANGULAR

ARCHED*

FS-36-XX-HTL

FS-36A-XX-HTL*

FS-42-XX-HTL

FS-42A-XX-HTL*

FS-50-XX-HTL

FS-50A-XX-HTL*

*Requires Arch Template Kit (not included)

Non-Combustible Mantel Projections

Figure 10.14 Non-Combustible Mantel Allowance - HEIR50

Note:

All measurements in inches.

Note:

Measurement is taken from

bottom of appliance.

HEIR50

1-1/4 IN.

1/2 IN.

NON-COMBUSTIBLE

MATERIAL

FIREPLACE

OPENING

MIN.

MAX.

Measurement from fireplace

opening to bottom of appliance:

= 44-3/16 IN. (HEIR50)

Summary of Contents for HEIR36H-IFT



































































Search results

Summary of Contents for HEIR36H-IFT

Reviews:

Heatilator HEIR36H-IFT, Installation Manual, Page: 50 / 66

Search results

Summary of Contents for HEIR36H-IFT

Reviews: