Heatilator HEIR36H-IFT Installation Manual Download Page 41

Page: 41 / 66

Heatilator • HEIR36-IFT, HEIR42-IFT, HEIR50-IFT Installation Manual • 2458-980 Rev. B • 8/17

Accessories Requirements

• This appliance may be used with a wall switch, wall

mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved

accessories should be done now to avoid reconstruction.

Follow instructions that come with those accessories.
• Hearth & Home Technologies recommends that Intel

liFire

Touch wireless controls be used for their fea-

tures and functionality with the IntelliFire

Touch igni-

tion system

Figure 8.2 Junction Box Detail

Electrical Service and Repair

WARNING! Risk of Shock!

Label all wires prior to dis-

connection when servicing controls. Wiring errors could

cause improper and dangerous operation. Verify proper

operation after servicing.

WARNING! Risk of Shock!

Replace damaged wire with

type 105º C rated wire. Wire must have high temperature

insulation.

GRN wire

inside box

Copper ground

attached to GRN

screw with GRN wire

WHT

BLK

14/2WG

Romex

Connector

NOTICE: DO NOT

wire

110-120 VAC to wall switch.

B. Wiring Requirements

Intellifire

™

Touch Ignition System Wiring

NOTICE:

Batteries should only be used as a power source

in the event of an emergency power outage. Batteries

should not be used as a primary long-term power source.

Battery polarity must be correct when installing batteries.

When using batteries as a power source, the 6-volt

transformer must be unplugged from the receptacle.

Do not store batteries in the battery pack when the

appliance is powered by the 6 volt transformer connected

to permanent electrical service.

• Wire the appliance junction box to 110-120 VAC for

proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT

wire

IPI controlled appliance junction box to a switched circuit.

Incorrect wiring will override IPI safety lockout.

• Refer to Figure 8.3, IntelliFire™

Touch Wiring Diagram.

• This appliance is equipped with an IntelliFire™

Touch

control valve which operates on a 6 volt/1.5 AMP system.

• Plug the 6 volt transformer plug into the appliance junction

box to supply power to the unit OR install 4 AA cell

batteries (not included) into the battery pack before use.

Summary of Contents for HEIR36H-IFT



































































Search results

Summary of Contents for HEIR36H-IFT

Reviews:

Heatilator HEIR36H-IFT, Installation Manual, Page: 41 / 66

Search results

Summary of Contents for HEIR36H-IFT

Reviews: