Heatilator ECO CHOICE WINS18 Installation Instructions Manual Download Page 10

Page  10

7065-144A

April 7, 2014

WS Series Wood Burner

A.  WARNINGS: AS/NZS 2918:2001 General Notes

WARNING: THE APPLIANCE AND FLUE SYSTEM SHALL BE INSTALLED IN ACCORDANCE 

WITH AS/NZS 2918 AND THE APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING 

CODE OR CODES.

WARNING: APPLIANCES INSTALLED IN ACCORDANCE WITH THIS STANDARD SHALL 

COMPLY WITH THE REQUIREMENTS  OF AS/NZS 4013 WHERE REQUIRED BY THE REGULA-

TORY AUTHORITY, I.E. THE APPLIANCE SHALL BE IDENTIFIABLE BY A COMPLIANCE PLATE 

WITH THE MARKING ‘TESTED TO AS/NZS 4013’.

ANY MODIFICATION  OF THE APPLIANCE  THAT HAS NOT BEEN APPROVED  IN WRITING BY 

THE TESTING AUTHORITY IS CONSIDERED TO BE IN BREACH OF THE APPROVAL GRANTED 

FOR COMPLIANCE WITH AS/NZS 4013.

CAUTION: MIXING OF APPLIANCE  OR FLUE SYSTEM COMPONENTS  FROM DIFFERENT 

SOURCES OR MODIFYING THE DIMENSIONAL SPECIFICATION OF COMPONENTS MAY 

RESULT IN HAZARDOUS CONDITIONS. WHERE SUCH ACTION IS CONSIDERED,      THE MAN-

UFACTURER SHOULD BE CONSULTED IN THE FIRST INSTANCE.

CAUTIONS: CRACKED AND BROKEN COMPONENTS,  e.g. GLASS PANELS OR CERAMIC TILES, 

MAY RENDER THE INSTALLATION UNSAFE.

WARNING: ANY MODIFICATION OF THE APPLIANCE THAT HAS NOT BEEN APPROVED IN 

WRITING BY THE TESTING AUTHORITY IS CONSIDERED AS BREACHING AS/NZS 4013.

WARNING:  DO  NOT  USE  FLAMMABLE  LIQUIDS  OR  AEROSOLS  TO  START  OR  REKIN-

DLE  THE FIRE.

WARNING: DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS IN THE VICINITY OF THIS 

APPLIANCE WHEN ITS OPERATING.

WARNING: DO NOT STORE FUEL WITHIN HEATER INSTALLATION CLEARANCES.

WARNING: FOR OPTIMUM PERFORMANCE FUEL MUST BE LOADED SO THE LOGS LAY 

“FRONT TO REAR” IN PREFERENCE  TO LAYING ACROSS THE WIDTH OF THE FIREBOX. 

SPACES SHOULD BE LEFT BETWEEN THE LOGS TO ENABLE OXYGEN TO GET TO AS MUCH 

OF THE SURFACE OF THE FUEL AS POSSIBLE.

CAUTION: THIS APPLIANCE SHOULD BE MAINTAINED AND OPERATED AT ALL TIMES IN 

ACCORDANCE WITH THESE INSTRUCTIONS.

CAUTION: THE USE OF SOME TYPES OF PRESERVATIVE-TREATED WOOD AS A FUEL CAN BE 

HAZARDOUS.

Summary of Contents for ECO CHOICE WINS18

















Reviews: